Could this LEGO Plastic Brick replace Concrete Masonry Units?

Chapters
0:00 Introduction
1:10 What is Lok N Blok?
3:40 Assembly
4:36 Properties
6:06 Concrete blocks
7:08 Plastic pollution
8:20 Sponsor
9:04 Pros
9:27 Hurdles
11:36 Conclusion

Lok N Blok is an innovative, easy to install, mortar-less, interlocking building block system. Its design enables quicker and easier installation than other building materials as it’s installed in fewer steps and doesn’t require specialized equipment. Lok N Blok is made of a proprietary mix of 49% recycled polypropylene, virgin polypropylene and fiberglass reinforcement. It also contains UV protection additives so it doesn’t become brittle in the presence of sunlight. It is smaller than a typical 8”x8”x16” CMU block. It is 12” long x 6” wide x 8” tall.

The block has tapered female dovetails on the ends and main faces. The slots measure 0.82” on the top and 0.53” on the bottom. Tapered male dovetails slide into these slots to create secure and strong connections. They can form flat ends, corners and even openings up to 6 feet in length with no additional header or reinforcement to maintain structural integrity. Square posts on the top surface of the block, fit into the square voids on the bottom surface of another block. This allows them to be stacked either directly on top of each other or offset by a quarter of a block or even half a block. There is no mortar or adhesive needed between the layers. The plastic webs in the middle have several purposes. They reduce the weight of the block, create room for additional insulation, and allow utilities to run vertically. Another cool feature is this circular void created when the blocks stack, which allows conduit and wires to run horizontally.

This system doesn’t require any reinforcement or concrete. However, you need to use a ⅝ inch threaded rod from the concrete slab or footer, through the entire wall. At the top of the wall, a compression spring nut holds the entire assembly down. All these features, especially the lack of mortar allows for quicker construction. It’s about 50 to 60% faster than traditional construction methods.

Lok N Blok is water resistant, chemical resistant, UV resistant, sound absorbing, bacteria resistant, easy to use, efficient and eco-friendly. It also has a high compressive strength, it’s lightweight, has high tensile strength and it’s fire resistant. That being said, it’s a new product so it costs more than traditional construction methods right now. It’s more expensive than steel stud walls and wood stud walls but it is 8% lower in cost compared to ICF walls.

---------------------
Disclaimer: The Amazon links in this description are affiliate links. I may earn a small commission for my endorsement or recommendation to products or services linked above, but i wouldn't put them here if I didn't like them! Your purchase helps support the channel and the video I product. Thank you!

This video was created for educational/informational purposes and qualifies as Fair Use. If you are the creator or own the footage featured in this video and have reservations please notify me via Youtube comments or email and I will accommodate you
#lego #concrete #construction #plastic #recycling #buildings #energy #ecofriendly #carbonfootprint

[thesilentcitadel]

Since this product has been in progress for 30 years, would have been good to see some projects where it was used already. Surely they have at least set up a demonstration sites and are gathering data on durability, fire testing, load tests, and a thousand other questions that they will need to answer to get it approved as a building material..

[GoatZilla]

Little concerned about how this would hold up in a fire compared to cement blocks, but I'd love to try it out on some smaller projects like a shed or something.

[lukedogwalker]

I presume that the blocks could also be disassambled? If so, they could be an interesting option for rapidly constructed temporary buildings whose components can be reused, perhaps to make another type of building, and which could be transported in multiple smaller vehicles rather than needing a crane and low loader to shift a shipping container cabin, for example.

[qgkhwsw]

Retired construction site manager, just wish this product had been available when I first started. Endless possibilities, good luck with the product.

[lolasso]

Polypropylene is actually a massive source of microplastics. Moreover, it has many additives such as BPA which are endocrine disruptors.

[VcrThunder]

Drawback! imagine the pain the Hulk must feel smashing through a wall and stepping on one of those giant lego bricks

[jacqjet]

My concern is about the very low temperature. I've worked with polypropylene for 40 some years. In Canada, a few days after the temperature had dropped in the minus 20 to -30 degrees Celsius, people wearing PP orthosis would be coming in the lab for repair, replacement. Also, in the heat, sheets tend to warp, especially if it was nailed on the top of a table.

[ggaub]

The ONLY cons are cost and regulations? I find that hard to believe.

[einarquay]

In Canada, where I am, insulation is a big building component. Vapour retardant and air barrier integration in this system would mirror methods in CMU structures. You’d never worry about rot either, as we do with wood frame construction.

[KhurtKhave]

Comparable build costs are not an answer to how much per brick. You could put it in big box hardware stores, even if noted just for sheds, retaining walls, and other small construction that doesn’t require permits and create your own billion dollar industry. But if nobody can get hold of it, it’s useless.

[JohnDoe-zlqw]

*Industrial Legos. I love it! My childhood building days will not have been in vain.*

[bennifrijolitos]

I would like to see this tested in 2k sq ft working homes in both high heat and freezing temps over 15 years.

[MikeTrieu]

I dunno. All plastics have a certain amount of elastic creep associated with them. Maybe the glass fiber reinforcement might slow that down, but I'd want to know those specifications before building with the material. You don't want to end up with a wall that sags over time.

[clairejeannette]

I saw some thing related to this in Africa, where they were using recycled plastic to make blocks that they’re using for building schools. Their system clearly isn’t as sophisticated as this but it was such a good demonstration of the product. I would love to see some of what has been built in Central and South America.

[bikerbobcat]

I'm an HVAC technician considering different material for a new construction home for my family. I'd love to see demonstrations of its insulative qualities, resistance to flooding, bullet resistance (this is America, sadly) among other things. Cool product with a lot of potential!

[ace_ofchaos]

You should definitely do a follow up on this. Some of the concerns people have in the comments are really interesting.

[tylercousins]

Bonding and attaching to it would most likely be very difficult. How do you screw to it? Eg, windows and door frames, drywall and other structural and non structural items that need to be attached to it.

[Pheonix]

I feel like there is less shown about the drawbacks than normal in this video, but I also hope something like this can become successful

[MommeeMadre]

This would be wonderful for setting up inside walls. Imagine adding, subtracting bedrooms as your children grow up! (Or move back😮)

[ahowlmx]

Saw this at the Orlando Build Show. Now skilled labor or DIYers can build a shipping container (but wider) shed in the backyard with a rooftop deck in a day or two. It was nice! Once they get a factory next to a plastic recycling plant it'll get cheaper but cost will be more than concrete.