Tamiya TT-02 alloy steering rack install guide

Welcome back to Wtf Rc Cars,

Tamiya TT-02 alloy steering rack install guide

1/10 RC Car Aluminum Alloy Ball Bearing Centre Steering Kit for Tamiya TT02 ￡14.16

SCHUMACHER CONTACT PRE-GLUED A30 CARPET SPEC - PK4 JR-A30KS £19.99

Surpass Hobby S1600M ￡52.66

For my kit I’m running 550 CST oil

Fastrax Tamiya TT02 Aluminium Shock Absorber Set (4) (55MM No Oil Inc) £29.99

Tamiya TT-02 Senna build and Essential mods finished.

399 Sheffield Road,
Chesterfield
Derbyshire S41 8LS
01246 942777
Showroom Opening Mon-Sat

Tamiya 58711 McLaren Senna -TT-02 chassis

Tamiya 54559 TT-02 Low Friction Suspension Ball (4 Pcs.) £7.50

Yeah Racing Aluminum Main Drive Shaft Joint For Tamiya TT02 TT02B £7.19

Yeah Racing Aluminum Main Drive Shaft For Tamiya TT02 TT02B £4.99

Yeah Racing Spring Steel Shaft For Tamiya TT02 £21.19

TT02-017 Yeah Racing Steel Front/Rear Gearbox Joints Tamiya TT-02 £12.25
TAMIYA TT02 TT-02 TT 02 Bearing Kit (COMPLETE) 16 Bearings £8.49

[Deaf]

Hehe every time I am looking for some solutions, your video always pop up. Great stuff buddy

[ebandcamp]

I also used the Yeah racing steel CVA’s all around , yeah spindle housings, yeah upper camber links . Shimmed them up where needed . Same on the rear with a 3degree toe in rear spindle housings. There is no play anywhere and free movement . Used the yeah titanium screw kit and the hard Tamiya chassis . Carbon fiber shock towers, bumper brace and battery hold down to keep the weight in check. Replaced most machine screws with titanium ( gets expensive ) . Used the stock plastic lower arms all around for a cheap to break point that hopefully won’t effect the more expensive aluminum parts . Hobbywing 21.5 brushless motor and speed control 68 tooth spur and for now a 22 tooth pinion . Need to order some 23-25 tooth and check temps . Car handles excellent . Almost hard to flip it ! .have the GT40 version but I put on a lighter Camaro body which I have yet to race . I shaved a lot of weight and kept most of it low as possible to keep the CG low . Strengthened it as much as possible . Was thinking shorty packs batteries but car was designed for the larger packs actually NiCads . But am using 5000mah LiHV graphene packs which are a little lighter .
Again good luck with your build . I’m nearly done . A couple more titanium screws here and there . And a long wait getting them from Hong Kong to USA. Next I’m going to be doing a stock only LOSI NASCAR for some oval racing after Christmas .

[ebandcamp]

I bought some titanium 25mm long screws ( thinking 20 mm may have been better? May grind them down ) and aluminum locking nuts on the bottom of the chassis with all the washers .
Rock solid with aluminum turnbuckles . Don’t have any play at all and works flawlessly and a lighter setup .
Good luck with it !

[vincemendoza]

Just finished the playlist (Slow day at work 😂) Thanks again for making this series. Very informative! Hope to see an XV-02 build one day?

[alfredomendozajr.]

I love the body of your car. Thanks for sharing this video.

[herbieRCpaints]

Excellent video, nice informative guide cheers 👍👍

[scaleworksRC]

I know it's kind of an old video, but if you have some spare thin washers around, you can put them between the top of the hex screw and the top of the bearing. It still has a slight bit of play, but it's much less jiggly.

[aezepi]

Nice vid. I have what I think is a tb03 with no steering. Would this kit also work with the tb03 and what servo mounts do I need? It’s my first tamiya and I have no clue what parts to get. Thanks in advanced.

[All-rc]

I found that most of that play is the front A arms. I have a video on fixing that. I just attached some supports. Feel free to check out my vid👍🏻

[dman]

Geez thats a noisy servo you're using

[andreaskassner]

That's not an improvement. It is horizontally unstable and the steering levers go up and down like a seesaw.