Worx Landroid Installation Guide

Welcome to the Worx Landroid robotic mower installation guide. In this video, we'll go through the steps, tools and information you'll need when installing your Landroid.

[Onyourbiketoo]

NB : You show installing around the fountain bowl at 10cm. Howerever, it has a raised edge so it should be at 26cm as if it was a tree.

[rbtx]

I have a large island (around 3.6 x 3.6m). What will happen if the Landroid is running low on battery and finds the island first instead of the boundary? Could it be stuck going in circles around the island, expecting that the wire will eventually lead it to the charging station?

[funnyvideosutube]

I live in tropical sunshine Scotland, lol is this thing (electric prong charging station) even weather proof, there's no mention of cover sheds anywhere

[concunningham]

Hi Team. Just took delivery, hoping to install tomorrow. I have some stepping stones that run from my patio to an outside office- they are pretty much flush with the lawn. Do I have to delineate these with wire, or will the gizmo just happily mow over them?

[stonehead]

Hi, what if the distance of the object like that fountain or the flower bed is less than a 1m to the edge, then what to do?

[metal]

Hi, i'm french and bought the new WR 165 E robot is it the same tuto ?
And for trampoline, is it ok without the detector but only with the cord?
Thanks

[davidmllebjerg]

I just got one today. It works fine but I sent it home once from my phone. That's when it hit a no go area around a tree and decided to follow that home. Only it just kept going around and around the tree. Any suggestions?

[romanstekliain]

Hello, just purchased a L2000 model and figuring out how to lay the wire. I have a place where two wires converge into a point, i.e. a path and the fence. how tight a loop can I make for it to cut a maximum space? Didn't find helpful advice on this in the manual.

[tis]

У меня участок более 1000 кв. м. Имеющегося кабеля не хватит, чтобы ограничить зону. Как в этому случае кабелем наращивается дополнительная зона для робота? Спасибо

[jessekoenig]

I recently purchased a used model which did not come with the triangle piece for right angle turns. Could you provide the dimension of that so I can cut out an approximate to use when laying the wire?

[jeff_]

I have section of about a foot and a half of grass between my patio and swimming pool. If I put boundary wire around pool and patio, will the landroid mower have any issues cutting in-between this section? Thanks.

[mawdkirynn]

We have lots of trees but have ordered the ASC Do we still need to run the cable around the trees ?

[dustins]

I like to see the use of the magnetic Flux of the conductors to cancel out another conductor. As a diesel tech I have to make sure i do the opposite to not disturb other circuits and their individual magnetic Flux fields.

[montepaso]

How can i create island if it is 60cm from the edge? Will double wire in angle work?

[reesepatel]

Hello, is the transformer and cable connector waterproof as I see it has been plugged and mounted outside, and the plug is in a waterproof socket!

[adrienroussel]

Hey Nice vid. What are the tringle exact dimensions? I can't find mine anymore.

[xreviews]

Isn't the barrier wire just 16 or 18 gauge insulated wire? The reason I ask is my house is in the middle of my yard and I would like the mower to mow all the way around. What happens if I just make a perimeter around the yard but not the house? Is it like a robot vacuum and will just turn if it touches the outside house walls?

[free]

How close do the wires have to be to each other for the signal to cancel out if i want to create a no zone area? If the wires were approximately two inches apart would that also cancel out the signal?

[kc]

How to make Landroid cross the driveway and mow another side of the lawn? Certainly buying two Landroids for a lawn is expensive and I wanted to see if there is a way to solve my issue by using a Landroid L.

[kjmullinz]

You need to go into more detail on how to hook up the wires to the charging station. I'm still getting an error that says wire missing