Setting up the BTT Pi (or CB1)

preview_player
Показать описание
How to install the system software to get your BTT Pi or CB1 system up and running with Klipper, Mainsail, and KlipperScreen. This is a little different than setting up a Raspberry Pi, but is quick and easy!
00:00 Introduction
00:33 Getting the OS image
02:05 Flashing the Micro SD card
03:08 Configuring the OS (name, time zone, network)
03:46 Enabling the TFT35 SPI driver
04:22 Booting the host
04:48 Getting into Mainsail
05:13 Conclusion

Links to the boards and display-
Рекомендации по теме
Комментарии
Автор

I did pick up a couple BTT Pis even though I didn't have a printer that needs one. The price and the ability to connect directly to 24V makes them a great alternative to a Raspberry Pi. Setting up Klipper was a breeze following the BTT guide. I would add that it is not necessary to unzip the image file when using Raspberry Pi Imager but no downside either.

rods
Автор

Hello friend, do you have a video showing how to install KlipperScreen on BTT?

VenonBs
Автор

ok, i have a question, I can see you set up the sd card but you don't say where to put it in the printer, the btt pi (btt-cb1) v1.2 doesn't have an sd card slot, so i'm lost as to where the sd card goes.... can anyone help me out?

CriticalPaint
Автор

Does it work with HiveOs also? Linux based OS. Thanks

CheapCharlieMiner
Автор

The device-name and WiFi settings would be configurable from the raspberry pi imager-tool as well, isn't it?

JoopHbR
Автор

I feel like this tutorial stopped early. What on earth am I suppposed to do about the missing .cfg file?

randomname
Автор

After the installation, I can install everything like Klipperscreen and use KIAUH exactly like on a raspberry pi?

lukebabewalker
Автор

Using a BTT pi or a BT pi4b adapter with CB1 I cannot get an output on HDMI with a VERY rare exception when the image shows but I get no touch. I have multiple touch screens and all work perfectly with both win 10 and 11 PC and linux mint on a laptop. They even get a great image when connected to a PS3. The screens are fine and the touch works perfectly...except when connected to the BTT stuff. I know which HDMI port on the Pi adapter is active but tried both and neither output any signal. Even tried connected to a TV and no signal. I can't find anything online or in the CB1 manual on ho to specifically enable/disable the HDMI. I have made sure to comment out the appropriate lines in system.cfg for HDMI. I've configured a CB1 EMMC with an M5P+TFT35 so I'm familiar with changing from serial or display. I was using the pi adapter with a CB1 before one of the RAM chips on it overheated and burned a hole in itself so that CB1 was replaced. So far it's working perfectly with the exception of no HDMI output. Everything I've found says that the video is all going to be from the CB1 and not the pi adapter so I can't see what on the adapter could have died when the first CB1 went kablooee. I'm baffled and BTT has been no help. Best I get is to make sure I'm using the correct HDMI port (which I am) and they give me a link to the manual (which I already have).

Enjoymentboy
Автор

trying to use at BTT Pi V1.2, I cannot get the BTT PI to power off the terminals. I get a Green LED Light but nada. Hooked a screen up to it and it doesn't boot unless it is connected to the USB for power, with the JUMPER. I have the Terminals going to the LSR 200 bringing in 24v over 18AWG wire. Is there something I am missing?

farsidetruth
Автор

I just downloaded it and burned the image. I never decompressed it or anything. Worked fine.

toddtheZ
Автор

no information on how to connect the BTT Pi and screen to it. You got to be more elaborate when you wanted to take on step by step

kamhaq
Автор

I purchased a BTT pi 1.12, that acording to the manufacturer is equivalent (even better) than a RPI 3b... MY ASS! It's pure crap, setting up the OS was horrible, the stability is a **** shit and the optimization of the OS is horrible also... Dont buy cheap chinese clones garbage, just go for a RPI. Im running kliper with no issues in RPI3b even in old smartphone with linux deploy without problems.

Helio___
visit shbcf.ru