Saab 9-3 Ionisation Module Problem - P1312

P1312 Saab 9-3. Saab 9-3 ionisation module problem #Shorts

ionisation
ionization

[caractacusbrittania]

Another great find,
Thankyou,
When it stops raining I'll be doing this.

[caractacusbrittania]

Only just got round to doing this
But oh boy, what a difference.
Car is absolutely flying now,
Before it seemed sluggish, tired
And with a slight hunt on idle.
Thanks cyd, it's really made a difference

[fatoy]

Don't have any codes or problems as yet so ordered some grease as a preemptive measure, it came today absolutely no corrosion on connector but blathered it and plugged it back in. I also did ecu connectors and abs module before I forget where I put the tube. Great tip to keep problems from turning up me thinks

[chrisgunnphotography]

Thanks, noticed I had corroded pin the other day cleaning solved my issue!

[markusstrom]

Hi Cyclone, love your videos, they've helped me so much wifh my 2004 9-3 vector! Recently had the water pump replaced due to leakage and I got the car back last week. A couple of days ago it started to get occasional misfires when accelerating, and at the same time I got the p0101 code - MAF sensor getting odd values. Should I look for vacuum leakage or replace the MAF?

[kennethmoore]

Thanks give me the information I just bought me a Saab 93 about two weeks ago. your information help me help me fix my car thank you

[antonypost]

Ive been working on saabs for 8+ years now and usually when i get these codes its 9 times out of 10 bad coil/coils. Ive never once replaced ion module just replaced plugs and coils and never had a car come back for it not fixing the problem

[georgewaller]

Hi. Firstly. Love your vids. Gonna be using your oil change video this weekend.
I have a slight problem with my Saab. It’s getting an engine juddering when accelerating. (Auto gearbox) 2005 2L T.
I’ve replaced spark plugs. Worked a bit better. Coil packs all seem fine. MAF is fine. MAP is fine. Only thing I couldn’t check was the O2 sensor on the turbo as I don’t have the right socket. Any ideas? :/

[ianrobertson]

just recently got the p1312 code and going to try this. I took the connector out and cleaned the pins as well as cleared the code and it didn't come back instantly like normal. I will update after i drive it home.

[gman]

I currently have this code. I was going too change the spark plugs.I would like too perform this procedure also. I hope everything goes well.

[gltwn]

My 9-3 was throwing P1312. I cleaned the connectors with contact cleaner, cleared the code, and went for a long drive. Code did not come back!

[lspd]

Great video! Quick question, my 9-3 B207, jerks a bit when I idle. Often when the car is warm. When it jerks, the RPM also drop a bit for a second. This dosnt happen when i drive the car. Thoughts?

[bpbanpetkovic]

Hi dear,
I have Saab 93 1.9 tid from 2005, 110kw
I have some problems with automatic gearbox, when it comes to four gear it comes some time like it's in neutral. What it can be? Regards

[marcustoomey]

I have a lot of brown stuff inside my would that be the head gasket gone

[vortexgaming]

Still trying to find silly cone at my hardware store

[crybum]

I have an 2007 Saab 9-3 2.0T it cranks but no start starts with starter fluid. Got it scanned got code “P0725” engine speed input circuit” what do I have to replace? Speed sensor, CPS? help.

[MoSaabii]

I'm in Canada and we don't have 'Electrical Quick Clean' .. Can I use WD40 instead..?

[plasticbmw]

I'm pretty sure that's not how you Wana use dielectric grease....please tell me if I'm wrong but I normally use just enough so it doesn't squirt out..mainly so it doesn't attract dirt and dust....good video though 👍

[ΑδαμάντιοςΚανέλλης]

Hello! I have a problem with my saab 93 2003 Aero. Its power is less than normal. The throttle is a lot weaker. But i have noticed that while i am on trip and have steady speed, with or withour cruise control i am getting a little blank brake and then the throttle is weaker than before. It is already weaker but it becomes weaker and its like i have 50hp. I have changed ECU, throttle body and gas pedal. My mechanic cant find the problem. It seems that has something to do with its electrical components. Turbo is working 100% correctly and the meter goes to full when i am on full throttle but the car doesn't give speed. Any idea in order to guide him?

[scottboughton]

solved my p1213 lying wires for coil 1 first then 2-3-4 so wires for coil 4 are on top of other 3 tryed without sucsess changing coil pacs 1and 2 new plugs and swapping knock sensor with known working one without sucsess code not came back for 3 days