Brake drum easy remove

removing brake drums with bottle jack (modified with weld) the car is Dacia Logan so before you laugh out loud just understand the principle of rear bearing hub and brake shoes &drum

[lexicase]

Love seeing all the experts here, this is a sealed type wheel bearing that is obviously seized onto the stub axle, you can see when the drum is finally removed that the brake shoes weren’t holding it back at all. Ford ba/bf front wheel bearings require the same brutality to remove and you gotta cut what’s left of the bearing off with a grinder.. I’d say having made this Jack tool, this person probably does a lot of the same vehicle type and made a tool for the job. (Bit concerned about welding to a bottle jack though ngl 😅)

[kunduz]

Честнр говоря ТАКООГОО я ещё не видел.Мололец автор.Жаль только, что приваренные планки придётся срезать для дальнейшего пользования домкратом.Хорошо бы продумать съёмную версию крепления.Очень понравилось приспособление.Лайк.

[lawrencewheeler]

Brakeshoes are extended! Either release parking brake, or use the star wheel to back off the shoes!

[bmwigearhead]

removes drum... pulls brake shoe hold down pins straight though the backing plate, while simultaneously breaking two ears off the brake slave cylinder. Brilliant...

[hybridamericandude]

Alternate title: How to easily destroy your drum brakes if you don’t understand how they function, and doubling your work.

[rohinhans]

Or just loosen the rear brake, that's what the little hole is for

[josealcala]

Maybe release the parking brake first 🤔

[rickigunter]

Forget all these comments I've done some big trucks and I knew I needed to replace brake shoes so I didn't care if they got destroyed but I did care if I couldn't get the drum off and I think this is a great idea

[OwenMotors]

Or you could just smack it like the rest of us

[HolyFix]

This is actually very cool. Some shoes don’t have a spot to release the tensioner. Ive had to torch a hole on drums to get them off.
They should make this tool because it can double as a tool to push In the cv shaft if it’s seized to the hub.

Also if you have to pull this tool out obviously you are calling the brakes and hardware as a technician. Ain’t no brakes to save here. Also hardware is only 10-20 dollars and is usually rusted and replaced. That’s all that would get damaged here.

[seanogreen]

He's got he's got one of the cleanest shops I've ever seen it's like as if he's never worked in there before

[mosespolk]

The two holes on the outside of the drum were me so you can run bolts in it’ll push against the back plate and push the hub off

[saturnmedia]

Uhhhh. I mean, if the goal is to replace the wheel bearing assembly, then yeah you did it right.

[podunkpennsylvania]

So many brake repair videos. So few with actual talent/experience /solid technique

[masonxbm]

Using a hammer would of been safer than welding brackets to that bottle jack

[dreweburgess]

How to destroy a wheel bearing easily more like, some people are idiots.🤔

[bobanderson]

They usually back off the star adjuster.
It might take a couple smacks on the face of the drum with a hammer but usually doesn't require anything more extreme.
Sometimes a little bit of WD-40 on each bolt stud where it comes through, and around the axle where it comes through doesn't hurt Especially if you're doing a pair of them spray them both down and do something else for a little bit.
That pinging noise when the drum released was the brake shoes snapping back on to the backing plate because he probably didn't back them off first.
Still a creative way of using a small floor jack good idea

[ChristianValdebenito-kd]

That tool with the hydraulic jack is good

[darlene]

Wow. I did my drum on my 93 with a crow bar. It came off easy 😊

[madmikemadera]

Another genius idea 🤣 .. you'll only need to remove the drum and you try to destroy the bearing