Vello FreeWave Fusion Remotes

Trigger your camera flash and Studio Flashes. Remote to release your camera's shutter.

Vello FreeWave Fusion Remotes

[BandH]

@atelzzz To trigger both camera & off-shoe flashes simultaneously, you would need a FreeWave Fusion on each off-camera flash to be triggered, as well as one FreeWave Fusion on-camera, the appropriate Vello FreeWave Camera Release Cable for your camera model, & an extra FreeWave Fusion Trigger to hold in your hand to trigger both the camera and off-camera flashes simultaneously. Ensure all triggers/remotes are set to the same channel frequency so all items are triggered together.

[amsguy]

I bought the transmitter/receiver set, along with an extra receiver. I want to use one receiver as a shutter release, and another receiver for remote flash. Even though the remote flash goes off when I press the remote, it is clear from the picture taken that the flash either goes off too early (I think this is more likely) or too late relative to the shutter. It has absolutely no effect on the picture. Is this scenario supposed to work? I read a comment on your product page that this won't work, but some of the comments from B&H on this page seem to suggest it should work. If it does work, can you help me with the setup?

[atelzzz]

If I connect the receivers to my camera and two flashes, and holding the transmitter in hand, press the button. Will it release the shutter AND fire the flashes ? Or this setup wouldn't work.

[jochoi]

1) Yes, the sleep mode is active
2) Not sure what you means, but I am using Vello RCC-P1 shutter release cable with the end labeled "Camera Side" plugged into the Remote slot and the end plugged into the receiver
3) It is focusing by half-pressing but it just won't activate the shutter release upon full pressing. In manual mode, it doesn't do anything at all.
4) May be later
Chuck, did you by any chance able to make this work for GH1 or GH2 as advertised?
Thanks.

[jochoi]

Have anyone figured out how to use this trigger for remote shutter release for Lumix GH1 or GH2. The trigger I have is for Canon and Panasonic, with RCC-P1 shutter release cable. It will focus upon half-pressing the trigger but it just won't trigger the shutter release upon full-pressing. What do I have to do to make it work? By the way, this is the second trigger I received from BH Photo and it is still not working!

[renatorodriguez]

Can I use it to simultaneously trigger shutter and flash?

[NighthunterNyx]

These are the cheapest pixel triggers and they also have Sony version.

[spectrumphotography]

I have a Vello Freewave that I need help with. I was fortunate enough to get help a while ago on the phone from a B&H representative. I went through all the programming steps while he waited patiently, but I couldn't get it to fire my camera, even though the read-out screen was responding. Finally, some quirk occurred to him to get it to work. Naturally, I can't remember what that is; and of course, B&H is closed for a week for the Passover holiday. 
Does anyone here know what the simple solution can be?

[deewolf.]

does it works with gh4? if not please suggest me the product with suits gh4 from your store??

[atelzzz]

So I will need 2 transmitters (one on camera, one in hand) and 3 receivers (one hanging on the shutter release cable from the camera, and one for each of the two speedlites).

Got it. Thank you.

[BandH]

1)Is the sleep mode disabled in the camera? If so, the Panasonic manual says a remote will not work unless the sleep mode is active
2)Is the 4 contact pin plugged into the camera and the 3 contact pin in the remote?
3)It is focusing, but is it searching or completing the focus? Try it in manual focus mode to test.
4)Reset camera to factory default

C h u c k
askbh{at}bandh{dot}com

[BandH]

I contacted the manufacturer who does test all of these units. I do not have gear here to test.

C h u c k
askbh{at}bandh{dot}com

[joemahoney]

It's crap. Save your money. Receiver never worked from get-go