Rust Dissolver, Does It Work?? (Rustoleum Rust Dissolver)

Will it work!?
We put to the test Rustoleum Dust Dissolver on the floor pans of a very rusty 1984 Ford F150 Bull Nose.

This was a ten minute test, the bottle does say up to thirty minutes for best results. Perhaps longer duration would see better results.

[justinbieber]

DUDE, It might be the Angle or the Lighting, , , , but I think you need new floor pans, , 🤔

[vanmann]

If you don’t replace those floor pans, you’re going to know how Fred Flintstone got around.🤔

[mr.matthews]

It would have been really funny to start the video with the rusted out floor, then you spraying it on and in 30 minutes later you have a completely professional refabricated floor.😆 Just for kicks.

[bryco]

I used this on my AMC 304's oil pain on my cj5. The pan had surface rust pretty bad. I hosed it down and the got called into work for a repair job. I quickly just covered it in saran wrap and left it sit outside on a trailer. When I came back 5 hours later the pan literally looked like it had been sandblasted. I grabbed it and power washed it all off and then through it in front of a forced air heater to dry and then was able to paint it.. All in one night! The stuff works great.. Just take time.

[betabilly]

Muriatic acid does the same thing and cheaper too but is really dangerous to handle in any application. I use Rust Mort for heavily rusted areas on my Buick's rocker panels and found right away the rusting stops with just two coats. Now, in your case the floor pan is rusted all the way through so has to be rusted on both sides. It would be a lot better to fabricate and weld in new floor pans.

[KevinLSX]

Just got done washing it off my obs gmc trucks frame and im impressed. It went from a nasty orange frame to a clean gray. Left it on for about 3 hours and just hosed it down.

[voidisyinyangvoidisyinyang]

Just uploaded my Rustoleum Rust dissolving gel fix to my lower rear trailing mount brackets on the TrailBlazer. I kept at it and was satisfied enough to then paint over with the Rustoleum rust reformer paint. I left on the phosphoric acid gel as a stronger "rust reformer" to mix in with the paint. Then left that to dry and then did a coat of the Stop Rust enamel rustoleum paint. Then finally put in the new rear trailing arm. Now only three more to go.

[freedom_aint_free]

This product is "phosphoric acid based" it's a much weaker acid than say muriatic acid, and it's much safer to use: Muriatic acid is actually Hydrochloric acid (HCl) which is actually a gas dissolved in water, so when you leave muriatic acid solution it puts out fumes of HCl, and it can dissolves iron to, so it is much more aggressive than phosphoric acid which is safe to leave overnight for instance, as it will only dissolve iron oxides (rust) and not the iron itself. So you are not using it to its full potential it needs more time.

[HARPOME]

Tried it and 30 minutes on real rust on sheet metal that has been wirer brushed and it took multiple treatments and 30 minutes turned into 3 days along with wire brushing it in to help and eventually left a clean etched metal surface. No way 30 minutes. Has creeper fumes wear a good mask when using along with gloves, eye protection and long sleeves. Got my forearm that looked like a scratch, but turned into a dime size burn .Not good if your in a hurry at all .If you have plenty of time it will work.Thank for the review.

[davebruton]

I always save spray bottles and triggers many have the various spray patterns . Wish you the best !

[nitenite]

he said a Goat pickle of a situation I been laughing so hard my stomach hurts 😂

[thatoneamericanguy]

Warning car has Flintstone brakes installed

[GRIDLESSLIFE]

Thanks for the review Jeff. I have my E150 converter camper van that I need to remove rust from. Will check this out. ~ Dave G

[johnthibodeaux]

It works really good if you brush it in.

[eddwinnas]

I use this stuff wrks well on freightliner trucks

[jasonbuben]

I’ve seen people use xy rust dissolver, it’s in a white bottle. It works good

[voidisyinyangvoidisyinyang]

I just uploaded my bumper transformed by this Rustoleum Rust Dissolver gel - rock on.

[v.e.]

Rust removers are OK for light surface rust, but you need to use a rust converter to really get rid oftherust. Otherwise, you're just wasting your time, effort and money. For the areas that are eaten through, you need to replace that metal or you're pissing into the wind.

[carriebrown-wolf]

I have some outside chairs that need a little of this! So happy to be subscribed now.

[imacarfreak]

Trying this right now on my 05 Silverado torsion keys... They are stuck in good. Don't wanna cut it up so gonna try this first.