How to Test & Fix Ignition Coil Fault Codes P0351, P0352, P0353, P0354, P0355, P0356 | Engine Codes

This video contains the followings:
----------------------------------------------------------------------
This troubleshooting guide covers these fault codes:
P0351 Ignition Coil “A” Primary /Secondary Circuit Cylinder 1
P0352 Ignition Coil “B” Primary /Secondary Circuit Cylinder 2
P0353 Ignition Coil “C” Primary /Secondary Circuit Cylinder 3
P0354 Ignition Coil “D” Primary /Secondary Circuit Cylinder 4
P0355 Ignition Coil “E” Primary /Secondary Circuit Cylinder 5
P0356 Ignition Coil “F” Primary /Secondary Circuit Cylinder 6
P0357 Ignition Coil Primary /Secondary Circuit Cylinder 7
P0358 Ignition Coil Primary /Secondary Circuit Cylinder 8
Also, it includes:
Ignition coil wiring diagram analysis
Ignition coil waveform analysis
Using Oscilloscope
Ignition coil wiring test
Ignition coil primary circuit test
Ignition coil secondary circuit test
Using the multimeter
Checking short to ground
Testing the continuity
Testing the open circuit
#P0351 #P0352 #P0353 #P0354 #P0355 #P0356 #P0357 #P0358

Disclaimer:
Any information contained in this video is just the understanding of “Automotive Diagnosis: Cars Repair & Training Guides” and it is not an official guide or reference, so everything provided in this video is just a share of our experience and understanding and they are provided as a courtesy for your reference only. So, if you are using any part of this video, use the information at your own risk. We highly advise you to check the manufacturer owner’s manual before performing any act of removal, diagnosis, inspection, or repair on your car to know about what you are authorized to do on your car, what the correct and legal procedure is and what risks might be involved, also viewers are strongly advised to consult a licensed person before any sort of inspection or repair. Due to the factors beyond the control of “Automotive Diagnosis: Cars Repair & Training Guides”, we cannot guarantee against improper use of information or tools or systems, or the procedure provided. “Automotive Diagnosis: Cars Repair & Training Guides” disclaims any damage, injury or loss caused by your decision to follow the steps provided in this video.

[AutomotiveDiagnosis]

Check out this video as well which is for testing any kind of ignition coils including Coil-On-plugs (2-wire, 3-wire and 4-wire types) and different kind of ignition coil pack:

[ravimech]

Looking forward to see more Fault code guides from you guys, this was great.

[carsrepaircenter]

Well done!
I very much like the section you explained the waveform, it was amazing to know that.

[sakhawatullahullah]

(Great sir) Please also include English subtitles

[SCSautomotive.]

Good amazing very helpful vedio thanks for you

[bobwillis]

My truck has been in the shop over 30 days. Codes are po 351and po356.Coils are new ECM is new.plugs are new timing chain new.All lines tested.Two new pinsin the connecter.On one and six wire.what else could it be?

[joshgieske]

08 expedition. P0357. Cylinder 7 new coil new plug new injector. Using noid light there is pulse going to coil but when I use the noid light on injector the injector plug will pulse for a few seconds after start up then shut off. All other injectors are good only cylinder 7 injector cuts off after start up. With power getting to the coil good coil and plug would the pcm be bad? Maybe bad injector driver in pcm?

[bobbyatman]

Hello, does anyone know if it’s possible to get p0354 if there’s oil in the spark plug well? Thank you

[miaroscarel]

hi..im getting fault codes for a and f at the same time..what do you think is problem..ive replaced All idnition coils and sparks plugs but still doing it

[toshibahomeschool]

P0103 and p0355 at the same time. Misfire in cil n 3. P0303 not detected. No vacuum leaks. Any idea? Thanks.

[ernestdamo]

Test ECM ground circuit : Measure resistance between ECM and chassis ground using the backside of ECM harness connector as ECM side check point. If the problem is found, repair it.

Specification: Below 1Ω please help me how to perform this one with multimeter