Full setting of ebike display (M5)

Are you looking for ebike with a middle display?
With the lightweight material, low energy consumption LCD display, shows battery level, speed, mileage, five levels PAS, there's no confusion when riding in the sun, you can clearly check the data that you want to know, making you better control your riding status, and achieve better exercise results.

[annespacedroid]

How do I enter & exit the settings page?? Is there a button combination I have to press?? 😊😅😂

[BuggyGamesYT]

P01 = Display Brightness
P02 = KM or MPH
P03 = Battery Voltage
P04 = Display Sleep Time
P05 = Pedal Assist Level
P06 = Wheel Diameter
P07 = 1? Motor Magnet Count?
P08 = 100 Max Speed
P09 = 0 Zero Start 1 Push Start
P10 = 0 PAS 1 Throttle 2 Both
P11 = PAS Sensitivity 1 Quick
P12 = 5 Max PAS Power
P13 = 12 PAS Magnets
P14 = 18 Amp Power
P15 = 39.0 Under Voltage
P16 = ODO
P17 = 0 No 1 Cruise (Long Press Down)
P18 = 100? Speed Ratio
P19 = 0? Power Bit
P20 = 0? Protocol
P21 = 0?
P22 = 0?
P23 = 0?

[maxheadroom]

What about p18, p19, p20.p21, p22 maybe you would have had more time if you did not long press up and down every time.

[simongh]

this feels like it's made by a bot

[iankelly]

Tip: Just go through each setting explaining what it does rather than exit out everytime and have to repeat again. It'll make your video less tedious.

[Milenkoff]

this video can't be watched until the end, it's very annoying

[JoelsterGk]

Thanks for the info but terrible video, you should edit the "long press the button" parts and go straight to the information. I'll make a better video.

[kingking]

When i do that it goes to a weird screen saying C
0000

[kadel]

The video is incomprehensible and worth nothing

[maxheadroom]

this is stupid how many times do we need to learn that long press up and down buttons gets you in and out of the programming mode. Also you did not mention sensitivity 1 to 24 which is more sensitive 1 or 24??? and you skipped 7 so how is this full explanation

[waltsmith]

M5 goes into blinking 0000 asking for PW or code. Bike supplier would not provide code. 9999 does not work or 1234

[jamesishere]

my only goes to 03p on my dyu any idea why?

[JAMARKOFILM]

My gogo bist ebike is an Ananda motor of 500w, I could not activate the operating system motor of m5. Can you help?

[lukatron]

My Pedal assist dosent work? Only throttle please help

[thebear]

Can you increase acceleration as my lankeleisi t750 plus dies at any attempt to use throttle only on a slight hill.

[C.Scholl]

Please show us a step by step guide on how to set the PAS 1/5 to 5, 10, 15, 20, 25kmh. And disable throttle and enable cruise control. I am sure you will help many people with a tutorial on how to do that. In my case it would be for a shengmilo mx03. Thanks ever so much! I subscribed to your channel 😁👍

[jasonbirghot]

Who knows wat error code 008 means and how to fix it?

[ksg]

Hello. I have an HM5 controller, but I can't access into settings with a keys like yours. How to access the HM5 settings????

[TheHappyDIYGuy-rinb]

This is so annoying long press too much, you don't have to keep saying it

[TheoOrlandoSystems]

Good morning,
Very unhappy with my CmaceWheel RX20, bought 7/2022.
After 6 months the Keyframe holder on the bike broke, so o had to replace the whole Key setup in the Battery. Not easy.
Now the Front Motor is not working for 4 months, but I was busy and did not report it, so it’s OUT Of WARRANTY, as 13 months and 95 km (yeah, that’s all).
The Factory support was incomplete, sarcastic and frankly shows NO knowledge of the bike (until I started yelling). What I can notice is RE-BRANDING to DUOTTS, Polarna, VAKOLE C020, which indicates to me that the original brand is failing! They should have fixed the problems first!
After additional testing and hours of work by myself,
1. Clearly the Controller is defective, so I am asking for an immediate replacement.
2. The Motor is also probably defective, but I am willing to wait for the Controller replacement. What worries me about it, is the cost and the danger that the NEW controller will be blown by the defective Motor.
Any ideas?