Whirlpool Washer Repair - Will Not Complete Spin Cycle - Electronic Control

This video shows you how to Diagnose and Repair a *WTW5000DW Whirlpool Washer W10634026 Electronic Control*
*Symptoms may include:* Will Not Complete Spin Cycle

This *Whirlpool* repair could apply to multiple brands: such as Whirlpool, Amana, Maytag, Roper, KitchenAid, Jenn-Air, Kenmore, Magic Chef, Admiral, Norge, and Crosley

*Fix it Yourself and Do it Right the First Time*

If we helped you, please support us and *Subscribe* to our channel!

Or send us a tip, so we can keep making free Appliance Repair videos

[niktesla]

This is so awesome. You saved me a ton of money

[mmcase]

Thank you much for posting these videos. I enjoy fixing things.

[meadowbyastream]

I know this video is old, but... we got a "helluva deal" on a matched set of these, got it home and hooked up, and had this very problem! It wouldn't drain. Researched for DAYS online (no, really.) Learned and tried calibration & diagnostic modes, even found error codes and all that (which it says btw, "takes too long to drain" ... like we didn't know!) We let it sit for about 4 days, and it suddenly started working - right after we purchased a new board. Sent the board back, it ran great for a month, then bam! Stopped draining again. Replaced the drain pump, made sure it wasn't plugged, etc.. still nothing. It's a royal pain to get it to go into diagnostic mode btw, both times we had this issue. We have to unplug it, press start to clear capacitors, plug it in, wait 10 min or so, THEN we can put it into diag mode - if lucky. If not, repeat until it works. Just bought a new board, so we'll see if that works. Really hoping you're right!

[kevingreen]

Why is it when I reset it and go to was all it does is fill up and wash won't spinout

[dwightmorgan]

Can the control panel be repair so that the soak light start working agen

[thorthunder]

I have a Cabrio machine. I tested the actuator motor for the ohms at the J16 terminal 1 and 2 but no ohms at all I then tested the black wire No.1 and the 3rd wire red and got 2.21 ohms. The book said test the 1 and 2 terminal so what am i doing wrong? Ohms should be 2-3.5 at 1 and 2 on J16 plug to motor but nothing. It seems that the terminals are not where they are supposed to be so what is wrong?

[SolidSnakeOnline]

I just got this in today. Brand new and it's not working, stuck at rinse. Wow!

[Digitonic]

Bought a Whrlpool toploader just like this it doesn't seem to fill with water very much before going into wash cycle is that normal even with large loads it starts wash cycle with little water

[clubberdang]

All thats how you replace a 400 dollar board in a 500 dollar washer. What a fucking scam

[terryelston]

I did the diagnostic and my wash and done light started blinking. What does that mean?

[oscarvillalobos]

I have a question, what can I do if my washer just fill the water and then doesn't start washing?
Is the same model of the video! Please help me and by the way it makes a lot of strange noises like if it is breaking 😢

[TheAudioDabbler]

I have this washer and it has stopped spinning. I can get it to spin with the calibration mode. I have went through a lot of the diagnostics in the manual. Question, the optical sensor is reading 12.04VDC but the manual says it needs +13VDC. Is that within working range? Or should I replace the control board?

[gypsyleezagates]

Do I turn the power on ? When I did it started to self clean

[dwightmorgan]

My whirl pool intelligent load is not completing its cycle the soak led is not working how can it be fix

[jessicamcmahon]

This is going way to fast for me to follow and write down directions. 🤦🏼‍♀️ do you have this procedure written down somewhere?

[FernandoLopez-cpbq]

The Washer it self was $500.00 new, and the contrl board is $277.00 plus Taxes and Shipping only works two years what kind of is this Whirlpool?

[stanainsley]

The sensing and the wash is alternating flashing with the done, any idea what that means

[randywarren]

Whirlpool wtw5000dw1 when trying to do a diagnostic test the lights don't light up Only the spin light flashes When you press the start button down to cancel it clears the light and start humming. When I spin the tub manually the humming stops. When I stop spinning the tub the humming starts again. Any suggestions would be appreciated

[dustydee]

where could I locally buy a logic board for whirlpool?

[ryantoomey]

Mine has an issue. Won't start, shows no signs of life at all. When I try the diagnostic mode nothing happens, there are no lights at all. It seems like it has no power.

Is there an internal fuse inside the unit that could be blown?