HOW TO Setup OMPHobby M2 and M1 with OPENTX Radiomaster TX16s - M2 Explore V2 and Original

How to setup the OMPHobby M2 Explore, V2 and Original version with OpenTX on the Radiomaster TX16s ! This video goes from start to finish and you'll be able to go from beginner to pro with this setup!

Products in this video:

0:00 Intro
2:08 Create a model & timer
5:25 Special Functions / Callouts / Timer reset
7:45 Curves
13:29 Reverse Channels
14:03 Begin Input Config
14:15 Throttle Curves Input
17:00 Gyro Input
18:55 Pitch Curve Inputs
20:46 Pitch & Gyro Mixer Page
21:29 Dual Rates & Expo
21:55 Widgets / Monitors
29:54 Prepare radio for binding
31:00 Receiver Install & Binding
32:38 Field Testing
34:58 REAL FLYING

Visit the stores!

Follow us on social media!

#buddyrc #omphobby #sunnysky

TJ's Beard Stuff - By No Shave Life

[BuddyRC]

*FOR THE UPDATED ESC: M2 V2 and Explore Use FLAT LINE THROTTLE CURVES*
Normal: 0-60-60

Idle 1 : 65-65-65
Idle 2 : 85-85-85

[tomlinjonathan]

Thank you very much for this tutorial. I have both the OMP hobby M1 and M2 explorer and have just bought a TX16s. Without this tutorial I would not have been able to switch from my old Futaba transmitter to the new TX16S! Very well explained you should go into teaching! Thanks again!

[jeffscheule]

Hands down the easiest to follow open tx programming I’ve watched! Used it on my Horus X10s with ease

[ilesfarms]

This is the best video of all I've watched regarding opentx Radiomaster. Very well done especially for beginners like me that have never used opentx. I like the ability to see the whole radio and the use of the navigation buttons. Shortcuts like copying curves and how to make a capital when labelling within the curve section.

[toy]

I'm new to these helicopters, but after watching this I had to buy a tx16s, it took me a few hours to set up, not all in one go, but it now works, thanks for your clear instructions, now I just need to learn to fly, a big thank you.

[davidsettles]

the more helicopter setup videos I watch the more I understand it. Very good my friend.

[stevew]

This video is going to be my PRIMARY video as a resource for heli setup. Like you said, there are many ways to do the same thing in OpenTx (I am a beginner to OpenTx). Absolutely fantastic and simple to follow!

[alishanmao]

This is absolutely a great tutorial my friend. many were looking for it. Personally I find OpenTx a pain to setup helicopters, but your tutorial makes it just easy as 123. You should get million views on this video but what can we do for Youtube Happy algorithm LOL. Congrats for such a good tutorial. I will recommend whoever asks how to setup opentx for helis, to watch this video. Oh and i like your beard man. Keep up the good work. and try a simulator like Realflight G7.5 or so, practice some 3D. you are going to love it. you will be hooked.

[haidaralbohamod]

This video deserves more than million views. What a great tutorial. Thanks a lot for the video

[Darediver]

Thanks so much for your teaching, for now on, setting up an helicopter to TX16S won´t be complicated for me at all.

[passinthru]

Good job! I was able to set up the OMP2 Explorer with OpenTX on a Horus X12S using this video. I did things a bit differently but used a lot of your process. Thanks.

[joesmoe]

What an outstanding video. I had used other videos, and were very frustrated. But yours was very easy to use and I was able to set up several helis on my Jumper T12 Pro that has been sitting for at least a year as I could not figure it out. Using a hobby grade controller makes a huge difference.

[WatsitTooyah]

Not sure if this has been suggested but you can just use 1 curve and 2 functions to set up idle up 1 & 2 curves. Just set this curve to the "!SE" option or whichever switch you use, the ! is a "not". This is also helpful for gyro stabilization switch on a 3 position switch. Thanks for the walk through. Happy flying

[ChickenHawk]

T.J. YOU ARE A GOD! A few days ago I purchased a TX16S Max from BuddyRC to replace my DX6e, I figured that it would be weeks before I could figure out how to use it with my M1 and M2. TY Brother!

[yali]

Great video, Thank you so much!
Questions:
1. I understand the Heli comes with OMP receiver out of the box, can you please cover that setup as well? I saw on multi-module website the channels are different.
2. In the Futaba setup you just showed, what happens if the flight mode is not FM1, i.e. 3D and you throw the Throttle Hold? Would it bring it back to -100%, which will cause the Heli to come down real fast?
3. I also saw on AccuRC a Rescue button, that could be great to see how to set it up

[gmodesike]

Thank you so much. Because of your video, alone, I decided to get the M2 Explorer and this radio. Thanks so much!!!

[icedragonfly]

Brah..u are a god!! after just finishing my rebuild of a tRex 450se, I couldn't quite figure out how to setup my jumper T16 after switching from a Dx6i with it so I could setup my blade pitch and get her flying again. Now also with this ill be be able to setup my blade-130x..thank u so much buds

[ronm]

Thanks so much for this video. I looked at a lot of resources and this was the easiest to understand and follow. Great Job

[HaiNguyen-iqgl]

Thank you very much for this. I'm completely new at this OpenTX and you have helped a lot.

[adriancjones]

Very nice and easy to follow. I would love to see you do a microbeast set up on same radio. It seems like it should be easy to set up, and I'm sure it is once you understand whats going on, but its a learning curve.