Training - M221 - M3.1 Implementation

preview_player
Показать описание
Training - Modicon M221
Module 3 - EcoStruxure Machine Expert Basic
First project
  1. LeTomas AHUMADA
  2. Schneider
  3. Electric
  4. M221
  5. Modicon
  6. PLC
Рекомендации по теме
Training - M221 0:22:02

Training - M221 - M3.1 Implementation

Training - M221 0:02:47

Training - M221 - M1.1 Introduction

Training - M221 0:08:53

Training - M221 - M4.1 Open , Short and Not

Training - M221 0:07:51

Training - M221 - M2.1 EcoStruxure Machine Expert Basic Tab Properties

Training - M221 0:16:06

Training - M221 - M3.7 Upload Application

Training - M221 0:12:01

Training - M221 - M3.2 Simulation

Training - M221 0:08:58

Training - M221 - M21.1 Conditional Elements (IF / ELSE / ENDIF)

Training - M221 0:12:52

Training - M221 - M6.1 SD Card functionalities

Training - M221 0:14:53

Training - M221 - M3.5 First Download USB Application + Firmware

EcoStruxure Machine Expert 0:07:31

EcoStruxure Machine Expert Training - M3.1 Getting started with POUs

Training - M221 0:47:25

Training - M221 - M12.1 How to use High Speed Counter as Single Phase

Training - M221 0:09:23

Training - M221 - M3.6 Online modification

Training - M221 0:28:02

Training - M221 - M5.1 Timers

Training - M221 0:19:03

Training - M221 - M7.4 TMH2GDB Initial Configurations

Training - M221 0:36:18

Training - M221 - M17.1 Introduction to Control Systems (Basic)

Training - M221 0:10:29

Training - M221 - M3.8 Connection via Ethernet

Training - M221 0:13:10

Training - M221 - M3.3 Debugging

Training - M221 0:30:48

Training - M221 - M9.7 IO Scanner for Power Meter Part 01

Training - M221 0:17:40

Training - M221 - M3.4 Implementation 2

Training - M221 0:03:21

Training - M221 - M2.5 EcoStruxure Machine Expert Basic Tab Commissioning

Training - M221 0:07:14

Training - M221 - M1.2 Legacy Migration part1

Training - M221 0:07:24

Training - M221 - M2.2 EcoStruxure Machine Expert Basic Tab Configuration

Training - M221 0:08:09

Training - M221 - M4.3 Edge Contact

Training - M221 0:08:22

Training - M221 - M8.3 Configuration Embedded Digital Outputs

Комментарии
Автор

Thank you for the video. It was very helpful especially in figuring out the UI elements.
As far as I know, It is not good practice to use Normally Open switches for "Stop" functionality. If the wire connected to the switch breaks, there would be no way to stop the conveyor quickly.
The person would then have to look for a disconnect or the e-stop, which hopefully was not also wired normally open.
It might be worth noting that there's a good bit of audio static in this video for some reason too.

marcfruchtman
Автор

Thank you for this great video. I have question please! Regarding to the POUs, Can I have multiple POUs in the project?? If yes, how is the sequence going ?? I mean which POU will start and which will be the end??? Is there priority for each POU???

Thank you

mahmoudelsayed
Автор

Thank you for the video. I have a question about the implementation of programme for reading data from encoders and convert to speed. For this, I must use a block for cyclic interrupt time and implement within a user-defined function block. Can I use the subroutine Periodic tasks in order to achieve this ?

tarekbenhacine