TANK LEVEL SENSOR + CERBO GX (Wiring & Programming)

Here are some additional resources that you may find helpful with planning and installing your DIY Camper:

[luisfelipeortizcruz]

Lots of videos talking about this but none explain as well and make it look as easy as Nate. Thank you

[markratliff]

Can you do a video on how to "wire" the CerboGX Relay 1 to an onboard generator. There are many videos showing how to "configure" the Cerbo but I have found very little regarding the physical wiring and components needed between the Cerbo and the generator itself. Thanks!

[stephencantbewrong]

Perfect timing. I was just starting to look into this as an add on to my cerbo.

[JeffinTD]

I can’t tell you how helpful your videos are. Thank you. Do you have one on the GX Tank 140?

[timlamarre]

This is an excellent video loaded with detailed, clear step-by-step info. Thank you for posting!

[ArcticNorthAdventures]

Thanks for this concise and informative video, well-explained without unnecessary tangents.

[gulleyteam]

Thank you for the video, a question. In a boat I have two fuel tanks that a joined together. Can I put a level sensor in each tank and somehow average them out? Thank you Martin

[TerryDalzell]

Just a word of thanks for all of your videos, different voltage than we have in Northern Ireland, but that's ok lol, i have enjoyed and also learnt a lot from your videos; so thank you so much, its all excellent. especially the electrical!

[bill]

How about doing a video on sensors that stick on the outside of the tank. Those ones with the floatie part don't work well in black water tanks

[pittipitti]

Hello, thank you for the video.
If i need to extend the cables, do you know which type of cable should i use?
Thank you

[peterbeer]

Great video! Do you maybe know if that levelsensor also works on the GX Tank 140?

[TheLifeOfRick]

Got this to work with the system I purchased from you. Thanks so much!

The screen will be in the front of the van.

I'd like to add an analog gauge in the back near the gravity fill.

Is it possible to connect the Cerbo and an analog gauge to the same sending unit? If so, what would the wiring look like?

If not, is it better to just add a second sending unit for the analog gauge, so two in one tank?

Thank you.

[drpaulgodard]

Super clear video... thank you! BTW does the voltage of the sensor (strange that it has a voltage as it is only a resistance) matter?

[johnclark]

HI Nate. Where do you get the plug block that the sensor wires connect? The block that has the 4 plugs on it.

[PTAddison]

Hi Nate, excellent video as always, have you a video on getting theVictron cerbo gx to display the watts when connected to shore power or do i need a ct clamp also my cerbo dosent obey my max amperage from shore power eg when max is set to 10A i could be getting 17A measured with multi meter, are these two items related
thanks, Phil in Ireland.

[pughy]

Great video! I wonder if you can help. My tank sensors on my verbiage GC are suddenly showing “disconnected.” How do I reconnect them!?

[dandotmp]

Hey thanks for this! I’m experiencing an issue where my cerbo says the tank is “disconnected” - i had to wire up an extension using butt connectors could that be an issue?

[danlash]

Do you have a link to a fancy tank geometry calculator? I have the s&b 35 gallon over the wheel well tank but not sure how to do the custom percentages

[cajuntravelers]

I have a grand design, can I tie my current sensors into the cerbo gx

[stilllearningagain]

Thanks for all the great videos. I was programming a sensor just this morning. with GAS. I ran into a problem with the "custom" setting.
it would only read two of them.. like when it showed 65 it wa really 62%.. and at 55% it was really 48%
but when I added the 3rd, pair, it never read it... tried several ideas but the when 3rd was at 41% it should have said 35%. but it always just showed 41. any ideas?
It deos have the latest Cerbo build 3.00~42
wondering if there is a bug?
THanks again for the Blogs and Videos.