Webinar: Generators Synchronization using DSE8610

Topic: Generators Synchronization using DSE8610
Speaker: Charity Africa (Application Engineer - Jubaili Bros)

For inquiries..
𝐂𝐨𝐧𝐭𝐚𝐜𝐭 𝐔𝐬 ⚡
📞 Call or Whatsapp: +𝟗𝟕𝟏 𝟓𝟎 𝟏𝟖𝟗 𝟕𝟕𝟏𝟔
📧 Email: 𝐣𝐛𝐝𝐮𝐛𝐚𝐢@𝐣𝐮𝐛𝐚𝐢𝐥𝐢𝐛𝐫𝐨𝐬.𝐜𝐨𝐦
🌐 Website: 𝐰𝐰𝐰.𝐣𝐮𝐛𝐚𝐢𝐥𝐢𝐛𝐫𝐨𝐬.𝐜𝐨𝐦

[piay]

Maraming salamat po.
Nagkaroon kami ng panuntunan at dagdag kaalaman hango sa literature ng gender control module. Naniniwala ako na kayo po ay Filipina na eng'r sa larangan ng elektrisidad.
Mabuhay po kayo.

[vamsiv]

Informative video about Gensets synchronization...

[nickagravante]

Thank you very much for kind share of technical support

[mitraline]

thank you to share about dse electronic.

[dominiquec]

Explanation very Clear, however some topic has not been covered such as masterless load demand

[charlescabahug]

Many thanks for sharing informative presentation. is the system needed to have synchronizing panel?

[Archie]

I believe in your explanation regarding the 4 generators feeding the load. Though the 4th priority generator started in the intial start up, the priority 1 generator will start, sysnchronize and share the load. Gen 4 will shut down thats how the priority system in Deepsea 8610.

[jeffreyechiemunor]

Thank you so much for sharing this video.
I want to know if DSE 8610 MKII can be used to synchronize both DG and Grid power or solar power.
Also what is the function of duty select configuration?
Thank you

[paulomeally]

when synchronizing generators does the DSE8610 has built in compounding current transformers or these have to be provided by the customer for each unit

[angelitocortez]

Thank you so much for the educational info.Can i apply this into paralleling to grid and solar.

[EngOmar-kzqv]

Dear Sir,

Please if I have a screen
DSE 8610 MKII and replaced it with a screen of the same type or you made firmware update, how do I transfer the SCADA settings for the screen? Do I record it before replacing or before firmware update and then manually transfer it to the new screen?

Best Regards

[renranrebalde]

Meron ba physical training o seminar nito?

[etiennewandonga]

Hi, thanks for the video.
Do you know how to remove the pin fro DSE 7320?

[manojsrivastava]

In case communication failure between Ecu and d.g controller how set it right and what are possible resons.

[ДимаКравченко-тп]

how to change the parameters on the panel 8610 to control one input in the absence of three phases, it turns on so that it turns on, and when three phases appear, it turns off.

[mohsenjalali]

hi. Can we use dse8610 with out ECU connection? because our diesel engine doesn't have ECU.

[dicksonfredrick]

When dse8610 MKII used for synchronization, is it compulsory for remote start signal connection on each generator? or msc link will perform that task?

[iroshanlahiru]

Hello, i have follow the instructions 2Gen synchronize perfectly but there Circulation current very high wht is the cause

[fryadsalih]

could you please give information in GCP-1 CONTROLLER and 6000 series regarding synchronization please

[rajeshroydsouza]

Dear, what is the difference between 8610 LS and 8610mkii LS