Quasar ARM Metal Detector - setting up the new coil

This video shows the essential setup for the new YourDetector Quasar ARM Unit or the setting of the new Search Coil for the Quasar ARM
The steps are:
1. Ensure there is some PWM value (just put 20 for the beginning). The current value is not important
2. HW Options / TX Freq - Enter this menu and perform the Auto (press UP) tuning of frequency. Press OK
3. Go to the HW Options / Coil Balance, and set the Desired Balance (so far just put the empiric +175mV and +45 Degrees)
4. Activate Compensator of the Balance by going to HW Options / Coil Balance / Balance, and by pressing Auto (UP). Save the Compensator by pressing OK.
5. Enter the HW Options / Ferrite Zero, press Auto and introduce the Ferrite Specimen to the coil. Hold it still once you will see some Value/Signal. Once you will get the Ferrite Angle, save it with OK.
6. Go to the Main Screen and swing the Ferrite Specimen above the Coil. In a noisy environment, you can hear random signals, but there should be no "stable signals" in the 1st or in the last sectors of Signograph. If there is such a signal, you should manually tune the Ferrite Angle pair of degrees to the right or left. For doing that - go to the Ferrite Zero again, and try increasing/decreasing Angle manually pair of degrees. Press OK and get back to the Main Menu for testing.
7. Check reaction to the targets. The coin or ring should produce clear SINGLE signal in 10-20cm from the coil. If there is DOUBLE signal, - just invert Ferrite Angle manually by 180Deg. (e.g. "-45" becomes "+135")
8. Enjoy your Quasar ARM from YourDetector!

If you just made the Factory Reset - you will most likely have to turn the FM Transmitter OFF in order to get the internal speaker working, otherwise, you will hear no sound.

[sebastiansek]

Terrific video. My Quasar is now quiet as a mouse, except when it matters. Thx

[chrisleigh]

Awsome training video. Im looking to buy new coils :)

[christopherwhitcomb]

I’ve had my quasar arm for a while and bought a coil but it didn’t come with ferrite and wondering where I can source a piece in the United States? Don’t mind ordering from another country if need be. Thanks for the video. It definitely helped me some.

[kraczek]

I've got a problem with my Quasar ARM.
Signal that i recive from coil is very good, strong and clear. But it is problem with position of items under coil. For example .
If you can imagine the coin under sand. Than f i move coil direct above the coin, there is no signal. But (it depends) if i move coil a few cm in front of or behind the spot it is clear and strong signal.
That means. I need to dig not under the coil where signal sounds But in front or behaind the coil. It deppend from coil balance or ferrite zero Point.
Can you help me with this problem??

[chrisleigh]

When you buy a new quazer of ebay with the coil they send. Do you need to do this to set it up ?

[christopherwhitcomb]

thanks for this video. I have a quasar arm i could't get to work till i watched this video, do you know what the latest firmware version is?

[kurkradford]

Very good training on a a great adaptable metal detector. Looking forward to the next videos. Any links to coils we can buy?

[bayuprihambodo]

can the quasar use a gold finder coil that has been modified at the TX RX pin out and has been adjusted to the quasar pin out, TX = 760uH and RX = 8800uH. can this be used?

[oligrandt]

Hello what are the Hardware fix when i use higher frequency thx oli

[brunoperrot]

Ello thanks for the response, very good machine, very good chanel, top ! 😉👋🇫🇷👌👍👍👍

[juanjosemartinezcheca]

seria interesante que hicieran un vídeo explicando la configuración del guasar arm ya que yo compre uno y no puedo configurar .saludos