HOVER BOARD MOTOR HACK / BALANCE BOARD

In this video we go over how to remove a hoverboard motor and get it to move at a controlled speed using a cheap 3 phase motor controller of ebay

Bracket used to hold wheel shaft:

[reuvenk]

Hello, did you connect all 4 motor controllers to the same Arduino? Can you share the code you wrote on Arduino?

[hajjism]

Thank you for your nice diy A-Tech. I just have a quick question please. I have made a mini bike using one of the two motors from hover board. But when I put up the speed, the motor slowing down and stops. Could you please help on this case? Thanks

[stevenpleasant]

Hi, this is good info thanks were did you get the Hoverboard motor holders from the Aluminum brackets I need some like them for my project thanks.

[Himura]

I have the same controller but I am not able to make a code that allows me to brake when changing direction. Any ideas?

[thedshack]

Hi, my motor needs a slight push for it to start spinning, im using two 11.1v 40c 5200 mah lipos in series, any idea as to why this happens, same issue when i use a 35v PSU

Thanks in advance

[TheNikolasNick]

Can you give a description and dimensions of the metal motor bracket holders and the screw size needed please? I am referring to the brackets you use to fix the wheel shafts on that excruded aluminium frame

[ВадимСалтан-пд]

Hello! Can you send the circuit diagram for connecting the board to the Arduino and the code? thank you!

[paulstir]

I have a working hoverboard motor (tested on another system ), I have purchased a brand new 36v controller with lcd ( s866 ) brand new throttle and brand new hoverboard battery for my e bike project but I'm experiencing no throttle issues I have checked voltage and purchased 3 brand new throttles checked wires tried swapping around but still no throttle

[TheLordbruh]

does this board control the position of the wheel? I mean if you program the microcontroller and depending what is been read it can run in close loop?

[mohammadhammad]

this is realy great work but how can we brak this Brushless motor by using the same controller

[hrizouchaib]

I have 4 wheels can i controll them with only two card (one in each side)?

[christophertaylor]

so my motors have an adtional set of wires identical to the hall wires?

[Mylotheblacknwhitecat]

Hey question I have two hoverboard motors and esc there the same and battery everything the same from a hoverboard but I'm wondering can I use everything like the speed controllers with a foot throttle cuz I tried installing a foot throttle and it doesn't seem to work idk what I'm doing wrong maybe u can help me

[jeremyconder]

Do you have to have a speed control or can you do direct on off full speed?

[magnus]

Hi! Is it not possible to use the existing hoverboard motherboard as a speed controller, and simply send the arduino PWM signal to the board? - overriding the signals from the pressure sensors.

[waynewill]

Hi, can you help.... i have the new hoverboard motors with 6 hall sensors?? can you recommend a motor driver i could use or know where i could get one with PWM capabilities? Many thanks.... & keep making great content...

[reuvenk]

Hello dear, can you share the code for what you burned in the Arduino tool to learn?
Thank you

[وحدةالراقيللتصويرالمصورمحمودفت]

Thank you my dear
I can connect the motor of the smart scooter with us in this explanation on a current of 48 volts to take advantage of it to a greater speed

[UlfBartsch]

I have built this project. However, with an ebike controller.
The motor runs as it should with a potentiometer.
If I give a PWM signal with an Arduino to the controller, the motor runs very irregularly.

Do you know what the problem could be?

[convictions]

Is there not two moter wheels on hiverboard