How To Rebuild an ATV/UTV CV Axle

Shop Now | Everything To Rebuild A CV Axle

Rebuild your worn out CV Axle before dirt and grime destroy your expensive CV Joint. A good CV boot seal is critical for CV joint protection and longevity on your ATV/UTV. The Tusk CV Boot Banding Tool allows you to easily and properly secure your CV boot bands on your UTV/ATV. We demonstrate how to rebuild the CV Axle on a Polaris RZR.

Click Here To Subscribe To Our Channel!

Follow Us On Social Media!

[uio]

Great job!! Maybe something is wrong with me, but I found this relaxing to watch.

[mikecondoluci]

i just bought a set of rhino 2, 0 axels for my rzr 900 i opened the box and theres a bag with bolts and plates what are they for?

[seastacker]

Very nice. Ordering an outer ASAP for my General. I already replaced it on a trip, but am gonna rebuild the stock to have as a spare for next time. Great video!

[SwormCycles]

Well I just bought the Tusk CV boot kit and was sent some totally different "ear band boot" clamps that look nothing like the clamps in this video. Also, the Tusk banding tool that the video says you need does not work with the ear bands they sent me so that was a waste of money. You guys really need to update these video's if Rockymountain ATV is going to send out different stuff. Thanks to Cleon the tech chat guy who told me what kind of clamps I had after sending him a photo. I then googled the information and found out how to tighten them as I have never replaced a CV boot before.

[audrybella]

Great instructional video. Well done. I have a 2004 Yamaha Rhino 660. I get a bad "squeak" from the driver side front axle whenever I make any degree of a left turn. I have change the yoke bearings and the brake pads to no avail. I have read many comments about a "clicking" or "popping" noise associated with CV axle failures but was wondering if you think its likely my squeaking is also from the CV axle since it only happens when I make any degree of left turn. Thanks.

[kuladeeluxe]

Well done, hopefully that is the exact process for my Quadrunner 300

[michaelronneseth]

May want to mention that not all outer cv joints just tap off, my circlip had square edges and was designed to be compressed to release. As such and not knowing that, a couple of good taps blew the casting apart and destroyed the joint...

[speedway]

A very good inservice. My question centers around the cv axles not coming out of the front gear case. I’ve tried everything. I would appreciate any help you can offer. Thx

[darrylvaughnmorinify]

Great video, thanks - other than the grease thats supplied in the packet, what is the best grease for rebuilding the joint?

[patrol]

Well done and very informative, I tried to work on removing the outer cv it didn't go out of the axle I hammered the inner race but it was impossible to remove out, and I am sure it is a clip type . Do you recommend any way to remove the joint please . Thank you

[scottdowney]

If you have the original clamps reuse them, they are superior. To take them off, squeeze togther the tabs and lift end off hooks. They click together same way.

[daleyohe]

Hope do you check your front differential to see if it working properly I have a polaris ranger 2009 it's a 700?

[davebergen]

Where can I find the internal components for the CV Axle? I'm asking for my 2002 Sportsman 500. Thanks!

[haroldking]

I am trying to replace a front outer cv boot. I need to take off the outer cv joint with a punch and a hammer but it doesn’t move at all. Any other ways to take this off?

[Dan-qtkq]

What’s the secret to putting back axel into the machine with the ring on end.

[vaishnavh]

How to determine the shaft travel and shaft to atv baja vehicle

[akhileshreddy]

How much do you charge for a sponsored ad?

[conniemcnichols]

Going to need my polaris 300 4wd back axle rebuilt. 1st time doing. Your video help alot thank you. How can I order from your company if needed,
Karl

[basteng..turner-.work.]

Brother this my work dubai axle raplasmant

[corymargison]

Can not find the inner cup with raging cage and clips on your website for 2018 rzr 1000 highlifter front axle