Spyder Auto How to Install: 2006-2010 Lexus IS250/350 LED Headlights

This video demonstrates how to install a set of Spyder Auto 2006-2010 Lexus IS250/350 LED Headlights. This complete how-to tutorial guides you, from start to finish, through the installation process. It also offers helpful tips throughout to facilitate a successful installation.

-= TOOLS NEEDED =-
1. Small flat-head screwdriver
2. Phillips screwdriver
3. Ratchet
4. Long extension
5. 10mm deep socket

-= INSTALLATION INSTRUCTIONS =-
1. Remove the eight 10mm screws under the bumper.
2. Remove the two fasteners on the fender liner.
(Turn 90-degrees counter-clockwise and pop-off)
3. Pull back the fender liner.
4. Remove the 10mm screw holding the bumper to the fender.
5. Open the hood.
6. Remove the eleven push-pin fasteners on the radiator shroud.
7. Remove the radiator shroud.
8. Remove the three push-pin fasteners as well as the Phillips hood stopper.
(Above the bumper near inner-side of headlight)
9. Remove the 10mm bolt in the center of the bumper.
10. Unseat the bumper.
(Loosen it, do not remove it)
11. Disconnect the fog light harness.
(There are three plugs – one on passenger side, two on driver)
12. Remove the bumper.
13. Remove the three 10mm bolts securing the headlight.
14. Disconnect the headlight harness.
15. Remove the headlight.
16. Transfer over the bumper bracket.
(Take it off of the OEM light and transfer onto new light)
17. Bring new light over to car.
18. Seat the new headlight.
19. Connect the wiring harness.
20. Reinstall the three 10mm bolts securing the headlight into place.
(Note: Two smaller bolts and one longer one near the fender-bumper area)
21. Bring front bumper nearby.
22. Reconnect the fog light plugs.
(There are three plugs)
23. Reinstall the center 10mm bolt holding the bumper in place.
24. Reinstall the three push-pins holding the bumper into place.
23. Reinstall the Phillips-screw hood stopper.
24. Reinstall the 10mm screw on the side of the bumper.
25. Reinstall the two fasteners on the fender-liner.
26. Reinstall the eight 10mm screws underneath the bumper.
27. Reinstall the radiator shroud.
28. Reinstall the eleven push-pin fasteners on the radiator shroud.
29. Close the hood.
30. Installation completed.

[gmane]

Don’t normally comment but this has to be the most precise tutorial I’ve ever watched!!

[Tim-ll]

This is so well done, totally clear and easy to follow !

[russianwolfhound]

This was a very well thought out and executed video. The instructions were clear and concise, and the on-screen visual markers for the fastener locations were extremely useful and accurate.

Definitely one of the better "how-to" videos on the Tube.

[devon]

You guys did an amazing job at laying out the steps for this!

[kasoyking]

Thanks for the step by step tutorial. Simple and clear instruction made it very easy to make the headlight change

[INOA_OLE]

Yo this tutorial is well planned and thought out. Might be the best by far good job 👏 it made my transition very smooth and easy 👌

[bosmanragga]

5:28 But the new headlight is less brighter than the original

[STRUGGLESLOTS]

A direct link to purchase would be nice.. 🙄

[swervoOG]

can you change the bulbs on these headlights?

[khalilrakhshani]

I replaced my headlight now getting warning check headlights system what is the solution kindly guide me

[batzorogeo]

Very good video. I have issues with my bumper. It doesn't seat properly and got a small gap on the top side below the headlights from both side. Can you advise what may be the problem?

[ionicbreeze]

Hello, do you know what the second small connector on the headlight is for? There’s the main harness connector and then there’s a small 4 pin connector. It’s the 4 pin that I am unsure about

[michaelboibodas]

What kind of ballasts do these LED lights have? I heard the headlight unit without ballasts directly wire to the battery terminal are better and avoid ballast issues like the OEM ballast. Help!!

[twinn]

You're basically taking the whole front car apart for some headlights???

[tishoslavov]

made a video as it can be seen in the evening

[henryist]

Can i use my after market h11 9006 hb4 hid kit with these new headlights?

[rossharris]

I just put these lights on my 09 is250 and they look amazing! But since I put them on my afs off has been non stop flashing. My auto lights work so I don't know why I have the afs off sensor on.

[kevingonzalez]

If my car is xenon headlights will this work

[ghambaryaneric]

What can i do, if my led protector was broken down?Can I repair it, or i need to buy a new one ?

[Sarowar]

Can I install 2012 is250 model headlights to my 2009 is250? Are they the same housing and parts?