Ardupilot Arduflyer Quick Start Guide. How to setup APM 2.5 for arducopter (Part 1)

preview_player
Показать описание
DIY means Do It Yourself with What You Have, no expensive equipment needed. So, with a donated pair of soldering iron we began our first time soldering. Yes, first time! So, if we can do it, so can you. Solder tip is a little big, but it was free.

Where To Buy:

  1. diydrone
  2. How-to (Media Genre)
  3. Ardupilot
  4. Arduflyer
  5. APM 2.5
  6. Quck Start Guide
Рекомендации по теме
Ardupilot Arduflyer Quick 0:08:51

Ardupilot Arduflyer Quick Start Guide. How to setup APM 2.5 for arducopter (Part 1)

ArduPilot Basics 0:27:01

ArduPilot Basics

APM 2.8 flight 0:12:46

APM 2.8 flight controller setup | How to make Quadcopter with APM2.8(Part 2) | Mission planner setup

ArduFlyer 2.5 0:00:10

ArduFlyer 2.5

How to Configure 0:04:32

How to Configure and Setup APM 2.5 (ArduCopter) for Simple Flight Mode

ArduPilot ArduCopter APM 0:10:32

ArduPilot ArduCopter APM 2.5 Configuration with Turnigy 9X Transmitter and Receiver for Quadcopter

APM 2.5 setup 0:00:52

APM 2.5 setup

Ardupilot APM 2.5+ 0:03:54

Ardupilot APM 2.5+ Overview

ArduFlyer APM2.5 Flight 0:01:23

ArduFlyer APM2.5 Flight Controller

Ardupilot Mega 2.5.2 0:00:47

Ardupilot Mega 2.5.2 First Setup Made

Preliminary ArduFlyer APM 0:05:36

Preliminary ArduFlyer APM 2.5.2 Test

CUBE 4 mit 0:02:23

CUBE 4 mit Arduflyer 2.5

DIY Mini Quad 0:07:49

DIY Mini Quad w/ APM 2.5, ArduCopter 3.0.1 Basic Configuration and Maiden Garage Flight

ArduFlyer V2.5 test2 0:01:47

ArduFlyer V2.5 test2

ArduCopter 3.0 Setting 0:08:14

ArduCopter 3.0 Setting up and running a simple mission

APM 2.5 and 0:06:14

APM 2.5 and ArduCopter 3.0.1 Loiter Setup and Backyard Test w/ DIY Mini Quadcopter

APM 2.5 (V2.5.1) 0:02:36

APM 2.5 (V2.5.1) Raw Footage / No comment

Arducopter 2.9.1 default 0:00:48

Arducopter 2.9.1 default settings, first waypoint flight-Start

ArduFlyer APM2.5 Flight 0:04:59

ArduFlyer APM2.5 Flight Controller

APM 2.5 - 0:00:38

APM 2.5 - V3.0.0 Loiter

Ardupilot quadcopter flight 0:01:13

Ardupilot quadcopter flight practice - 1

GAUI 500X ArduFlyer 0:00:22

GAUI 500X ArduFlyer V2.5.2 Arducopter V3.0.1 Mission Planner v1.2.68 mav1.0

Arduflyer RTL land 0:01:25

Arduflyer RTL land test

Ardupilot 2.5 + 0:05:35

Ardupilot 2.5 + first flight

Комментарии
Автор

i found a setup with using two ubecs to power the input and output of the apm board separately. The redundancy is better for brown outs apparently. The diy forum said i need to switch the green and yellow cables in my arduflyer gps & transmitter cable. I tried, but damaged d cable:( whats d name of d cable that connects d gps to d apm ? did u cross the green & yellow wires? On d rctimer apm board, can u power everything(d servos, receiver, motor etc) through the HKpilot or 3dr power module?thx

crazytrinibago
Автор

hi what do i need to initially buy to setup the arduflyer(i already have d board, gps & telemetry) ? can u list it all from hobbyking or rctimer ? a) battery ? b) voltage regulator ? what is the name of the cable to connect the gps to apm ? i damaged my last one. thx, i just want a list of what to buy, not necessarily instructions. thx alot

crazytrinibago
Автор

I'm trying to set arduflyer for a boat and I want to use mission planner only to operate it.
I have arduflyer v2.5.2, Feiyu FY-41AP, USB port, GPS, Power manager, receiver, air speed sensor. what do I need more and How to set these parts...
I'm not professional

노현영-ts
Автор

My only question is: How similar is the setup of arduFlyer to the setup of 3DR's ArduPilot? Other than soldering, what additional steps did you need to take in the setup?
 

STRKR
Автор

Plz help. My apm 2.6 came without a jp1 jumper or the jumper pins installed. It will power up if i use the usb connection but does nothing when I use the power module. If I install the header pins for the jp1 will it work with power module?

MrNeil