How To Install A Sena 10C Communicator on an Arai Corsair X Helmet from Sportbiketrackgear.com

How To Install A Sena 10C Communicator on an Arai Corsair X Helmet

The 10C is the world’s first look at a fully integrated Bluetooth helmet communication system and HD camera rolled into one powerful device. It’s capable of full HD video (1080p:30fps and 720p:30/60fps) with 3.5 MP still shot image capture and shot, burst and time-lapse photo modes. Built to handle with ease the rigorous demands of outdoor sports, motorsports, and first responders, it is the complete solution for in-helmet communication and action videography under challenging conditions. The 10C is very easy to install, but we wanted to give you a quick reference guide to make your experience as easy as possible.

[RUBBERNMETAL]

Thanks a lot for this video. I bought an arai concept x today and left my old Shoei in the Arai box along with the instructions to be picked up later and couldn’t figure out how to place the earphones until I watched this video. Thanks for the guide it’s really helpful

[stacymahaney]

Thanks you! This helped me fit the Sena 50c to my Arai XD4. The XD4 doesn't have the obvious cut out space seen here but there is space in the XD4 pads that lined up nicely for me. After the speakers were placed in the pads it helped to tighten the Arai to fit more like my dirt track helmet (a cheap HJC). This was a plus for me.

[ptn]

Thanks a ton! Used your instructions to install a 10S in a Quantum-X.

I run a Small helmet, the speakers were just fine without the spacers. The smaller spacers caused my ears to fold lol.

[gawengs]

6 years later used this video to install my cardo. thanks

[WildlifeMoto]

Nice video. Used it to fit my Cardo, pretty much the same steps but boy are those cheek pads a pain to get back in. Thanks for the guide.

[Ignoravo]

This communicator system is pretty huge and I think it is going to affect aerodynamics. I prefer the slim look of a Cardo unit instead. Anyway, nice tutorial.

[roadtoad]

I find that the boom mike has the best noise cancelation and I recommend that route.

[CenobiteBeldar]

Installing this looks like a pain in the ass. Also, the nice thing about these finely made helmets is that they come with anti-micobial material in the lining, but with this installed it looks like it's a chore to remove it if it's not permanent in order to clean and wash the inner lining that's removable then reinstall this system again. My helmet has a BO smell to it sometimes. I need to take out the lining and have it cleaned, but I'm hoping when I buy the Classic V helmet that I won't get much of a smell.

[SlickMotoMike]

Oh I didn't know that you had to pull that back on the cheek pads hahaha I've gone through 2 intercoms and non fit was too tight and now I know why because don't stick to the helmet but the cheek pads lol

[seanmoaref]

After following all the instructions and finish installing, should the speakers sit next to the chicks and not directly over the ears ?? slots are closer to the mouth and away from the ears. not sure if it is supposed to be this way.

[ClutchFirst]

That's one sweet looking lid. Do you guys sell that helmet holder?

[TerryBollea]

Can you still fit earplugs in, or do the speakers touching your ears block out enough wind/road noise??

[nandhakumarparameshwaran]

Awesome product but it's a rain proof ?

[sheepish]

Would it be possible to show how this can be done on an 'Aria Chaser V'? as I'm having difficulty attaching my Sena 20s

[aslanyureky]

I've watched 3 other videos, they didnt helped at all. this is the only good video specially to install sena to arai helmet.

[kongzillagod]

The clamp on the side of the helmet sucks it doesn’t clamp very good

[Remo_]

I installed my sena the sound was shit and my expensive helmet now felt uncomfortable. My Dumas didn’t know arai put the cut outs being 🤦🏻‍♂️😂😂

[Rider_Tom]

Putting the cheek pads back in is impossible

[bigblue]

Left/Right.... Right/Left Left/Left Right/Right ... simple.