Making Carbon Fibre SPLIT mould. Motorcycle fuel tank PREPREG [OUT OF AUTOCLAVE] and Autoclave

Показать описание

Making Carbon Fibre SPLIT mold at home. Motorcycle fuel tank PREPREG [OUT OF AUTOCLAVE] and Autoclave carbon fiber

#composites #prepreg #honda #monkey #tooling
#vinylester #carbon #autoclave #diy #infusion
#fibreglass

Republic Of Composites

Рекомендации по теме

Комментарии

Why not fiberglass in a cross piece in the circular plug, so you have something to hold to pull it out? Or put it in the freezer as that’s what I do

TordenPSM

I have an experience in cloning flower pot. There was another easy way to open cylinder mold is by knocking from inside on the middle cylinder. It will make the air getting in.
Edit: or pouring hot water on it

iamocoyt

Do you think you can make a list of the products you use? possibly also the sites where you buy them?
I would appreciate it very much!

robert-claudiuwolf

maybe use some compress air gun can help release the mould

sendepowersports

Any video of how you make mold and how you use the mold before unmould? I Like to know how you make a closed parts

patata

What kind of release agent you using exactly ?
Does wax do the job very well ?
Is this closed part possible with carbon vac infusion ?

calico

Why is the mold resin a strange color? What is it? Nice tidy work!

nathanchalecki

Do you accept custom order for carbon fiber fuel tank?

TheGrandeinter

HI everybody.I live in north Virginia .Is anybody know where i can buy these matrials?

farhadnaraghi

I use a brand called Honey Way. Aply 7 coats. 15 min with first coat on. Buff it of. Waith 15 min. Then second coat ....and do it over until 7 coats is done.

bifftannen

I always see you use a small brush in every job you do in making fiberglass, is there a reason? why don't you use a big brush to speed things up a bit?

rahmatsiwi

I can see that u have an autoclave. This simplifies the process. Otherwise, u would have to use a soluble core. Good job, i dont know how long these fiberglass polyester moulds would last though

keronGR

Super 👍 mais le démoulage difficile avec le milieu des réservoirs

jeanfrancoispoivre

Making Carbon Fibre SPLIT mould. Motorcycle fuel tank PREPREG [OUT OF AUTOCLAVE] and Autoclave

Making Complex Carbon Fibre Tubes Using a Split-Mould

Making Precision Split-Moulds for Complex Carbon Fibre Parts

Fibreglass/FRP Split-Mould Making Guide (Carbon Fibre Airbox Pt.2)

How to make Carbon Fibre SPLIT mould. Car wing mirror cover. Prepreg [OUT OF AUTOCLAVE]

How To Make A Splitmould For Prepreg Carbon Fiber (Fibre) Parts - PART 4 Mouldmaking

Introduction On Split-moulds and Prepreg Carbon Fiber

😘 '4 ways to make Carbon fiber tubes' full tutorial online 08/09/22

Carbon Fiber Is Easy?

Making a Composite Mould for a Carbon Fibre Part from a 3D Printed Pattern

How to Cast a Two-Part Compression Mould for Forged Carbon Fibre

Composite (Fibreglass) Pattern Making Tutorial (Carbon Fibre Airbox Pt.1)

Using Sheet Wax to Create an Offset Mould for a Carbon Fibre Cover Component

How to make a mould for a carbon fiber (fibre) part

How to make a carbon fiber part in under 1 minute.

How to Make a Carbon Fiber Car Bonnet/Hood - Part 1/3 : Making the Mould

3D Printed Moulds To Make Carbon Fiber Epoxy Resin Tubes – How to Tutorial

Hand Laminating a Carbon Fibre Part Directly into a 3D Printed Mould

Making a Mold of a Plastic Part to Turn Into Carbon Fiber- step by step

Moulding Hollow Carbon Fibre Parts Using a Low-Melt Metal Mandrel

A NEW Way to Mold Carbon Fiber - Trapped Rubber!

How To Make Carbon Fiber Tubes - 4 different techniques (Tutorial)

Making A DIY Carbon Fiber Sheet

Making High Temp Carbon Fibre Moulds for Prepreg Using Resin Infusion

Using Foam To Create a Carbon Fiber Mold