Sonic Pad | Setting up custom firmware | skr mini e3 v2

Printer used:

ender 3 v2 with a skr mini e3 v2 motherboard, linear rails, sprite extruder

If I helped you out and you’re able to tip, I’d so appreciate any help! Thank you a bunch! 🙏 :)

[LittleLoudPrints]

Hey everyone. Just posting an update on the state of the channel.

I was recently affected by the tech layoffs happening(I have recently gotten a new job though) but before that I was hustling it to get a job, that combined with having a 1 year old has just made it really tough to upload. However I uploaded this video because I want to make fun and helpful videos and the goal is absolutely to do that full time.
Thank you so much for the support and I hope this video has helped you all in someway. Currently I plan to get a routine down that allows me to upload every week. I am currently trying to upload a video about the printer.cfg and how to set that up. I also want to respond to all of you in the comments and give you all a good response and solution for issues your facing. I’d also like to make this video again and give you an updated process. I hope to do this asap. I’ll continue updating the description with as many printer.cfg examples as possible for as many boards as possible. Thank you again!

[jeffking]

Appreciate the video. I'm trying to configure my sonic pad to work with 2 different printers, one which is a stock configuration and was plug and play, the other is modified to where I need to build a custom printer config file. I've found your video very helpful

[dempseydoodles]

I upgraded my SKR Mini E3 V2 to the SKR Mini E3 V3… can you make a video on how to compile info for that board?

[hendrix]

What do I need to change in the firmware generator page for a 4.2.7 board. I've posted and looked all over, but I can't find any information like the clock reference, the usb vendor ID, the usb device ID, or the GPIO pins

[billprice]

I have just tried this on my ender 3 with btt skr mini e3 v2, when i install the firmware.bin the sonicpad creates, it installs, as changes to firmware.cur but the sonicpar can no longer connect to the printer on the usb. Tried several !PA14 is set but nothing, i put marlin back on Amd works fin and usb connects as expected, any ideas please as i am now stuck!

[Toni.Sky_RGtr]

My Pad find no my printer.Cfg what Wrong i make ?

[jdittmann]

Sonic Pad is great if you have a stock Creality printer but i'm using an SKR 3EZ to run a 3V2 with DDX V3 / Mosquito and .9 degree stepper motors. If I would have known I'd have to setup a virtual machine I'd have just used an old laptop I have laying around

[CGK]

I'm stuck for the skr mini e3 v3 :C There's no option for the processor model for the stm32g0b1 even with the most up-to-date Sonic Pad firmware itself... Can anyone help??

[doctrainsmodifications]

Greetings, Thank you for a great tutorial which I used to to build the bin file for my SKR Mini E3 V3. The board flashed perfect and after some mix and match effort with building a printer.cfg file, BTT pin out configurations, I was able to get the Sonic Pad and the SKR board to work.
I do have an issue with the Self-Test feature of the Sonic Pad. It will allow for the hot end and parts cooling fan test to run and complete but it does not allow the Z-Offset, Bed Leveling or Bed mesh feature to show up. ???
A side note the SKR Mini E3 V3 is using the STM32G0B1RET6 chip which is not in the Sonic Pad listing.
A review of your " Compiling Sonic Pad for SKR Mini E3 V3 " does not cover the pad's Self-Test functions.
Any Thoughts would be helpful. Again a great job for showing how to build the bin file.
Doc'🤔

[rickyyym]

My sonic pad won’t read the printer.cfg file

[JonBallRealEstate]

this is for the old board. I have the 3 v3.0 so it doesnt have the firmware for mine

[peloy]

I CANT GET MY SKR MINI CONNECTED BY USB, it seems to be dead with the usb /serial port:( ANY IDEA? Thanks for the video

[unsc]

Is it possible to get the SonicPad to communicate with a printer with a CRtouch installed that didn't come with it by default (in my case a CR10V2)?

[Stoeffu]

Thank you for your Video. I have a Anycubic i3 Mega, but i don't can use it with the SonicPad. How to flash the Klipper Firmware on the Printer? Is there a HEX File to download to flash it over the Slicer on the Printer. My I3 is Standard but with 2208 Driver. Can you help me? Thx a lot. Chris

[sprlpy]

I do everything as you do, however, at the last stage there is no connection with the printer

[PaulParrott]

So, I followed the steps from your tutorial. I have a 4.2.7 board (new and verified) in an Ender 3 Max. I used the Github 4.2.7 board sample and edited only the items (dimensions) as it pertains to the printer for the print.cfg file and it still won't work. I just throws an error about "cannot infer homing_positive_dir in stepper y". I also get some sort of connection error if I navigate to a setup screen. I tried updating the code with homing_positive_dir = true or false and neither changes the outcome.

Any ideas?

[ypehille]

Hello, I am going to install a sonic pad on my ender 3v2 with the Sprit extruder. Is it possible to take your printer.cfg file en put that on my sonic pad just simply using copy/paste? zo al the settings like offset of the touch and other bed settings or used ??I hope you answer and understand my question, Don't have the same motherboard as you have I believe

[PrintingtogoimpresiónDMéxico]

Puedes hacer un vídeo de Sonic pad con kingroon kp5ll

[АндрейФ-яс]

Hello, please help, is it possible to create instructions for installing a clipper on a sonic pad of various models, such as kingroon or artillery or mks mini board for Ender priners.

[noway]

For all of yuo that font understad, i sugest to read the Klipper Manual, its very good and after reading yuo gone see that its not so complicated, good luck😊