Unlocking the Secrets of Soldering: Few People Know About This Secret Of Soldering Iron And Salt

Unlocking the Secrets of Soldering: Few People Know About This Secret Of Soldering Iron And Salt

Welcome to your ~ INVENTOR EYE family creative army.
In this channel you will find useful inventions,Tip and trick, Unbelievable homemade projects, Unbelievable projects tips hacks tools, Unbelievable uses old material, Unbelievable repairs,Awesome restoration, woodworking, homemade projects, Modification tips tools, Mastermind ideas, Mastermind repairing tricks, Reusable ideas, Recycle old things, do it yourself, How to make, Crafts ideas, Constructions, Old to new tricks, DIYs
Be a part of our family by subscribing to *INVENTOR EYE*
Look at everything with an inventor eye ||

#inventions #diy #inventoreye

[simonharris]

You know what would be better than music in a video like this? Some dialog explaining what you're doing, and why.

[dgakadoug]

Maybe it isn't readily available everywhere, but paste type flux intended for plumbing is usually based on zinc chloride, inexpensive and typically works OK on stainless steel.

However, as others have pointed out, zinc chloride flux MUST be removed to prevent what can become an essentially endless corrosion cycle. It should never be used for any electrical or electronic application. SOMETIMES it can be used in electronics for initial tinning of difficult to solder metals that are then cleaned thoroughly and subsequently soldered with a suitable non-corrosive flux.

The real key to soldering stainless steel is to lightly abrade the surface with fine emery paper before attempting to solder. SS relies on the formation of (primarily) chromium oxide on the surface to impart the stainless properties. That oxide layer needs to be removed to facilitate soldering. Ordinary fully-activate rosin flux will often work just fine on SS if the surface is freshly prepared this way.

[lenturnbow]

Acid flux. Not great for electrical work because it continues working and will corrode after the solder joint is complete. Please consider 'no-clean flux' instead. Then immediately brush 99% alcohol on the completed joint to get rid of the flux.

[xXturboXx]

Do NOT do any of this. It's toxic.

[weedhopperarmes]

Its always handy to know alternative ways of going about things but quick tip you should seriously consider tinning that tip

[AVKStudio]

Perfectly fine to open a battery bare hands, take some acid in a bottle and do this on the counter, instead of a high quality, inexpensive flux. Anyone reading, don't do any of this please

[tbone]

Kind of makes me want to solder and play the xylophone.😂

[Zedrich]

Me for no reason:
"Just gonna take a little battery acid in this syringe. Okay, see you guys later"

[seymorebuttz]

Cool stuff, lemon juice can also be used.

[gwjiwwo]

Why would you ruin a perfectly good s/steel ruler?

[matt-bbkv]

Cool to know you can make something like this from junk laying around, might be a day when thats all thats left

[jeffbaker]

I think it was the magic pink spoon that did the trick.

[edwardstone]

Model railroader here. Been soldering brass track joints by the hundreds with regular No-Korode paste flux for years. No issues with corrosion. Once the joint is made I wipe it all clean with denatured alcohol.

[warwick]

Looks like "spirits of salts" old soldering flux. You can get a better response using transmission fluid! Simple and easier.

[zacandmillie]

Very handy to know... if I want to ruin a nice steel ruler

[taiducvlogs]

Cảm ơn bạn đã chia sẻ video clip chúc bạn thành công.

[jokkey]

Just get sulpheric acid, add zinc and allow to cure. You can soft solder stainless and antimony too. No need to use a special measure stainless steel rule.

[iojlntj]

Çok güzel olmuş ellerine emeğine sağlık

[CooLDEaFYMe]

Its annoying music while watch video 😅

[killzoldek]

Nice, but you should mention that the smoke produced by the heat is really toxic.