Heat pump tumble dryer test mode Aeg, Electrolux, John lewis, Zanussi

Finding your problem with a heat pump tumble dryer can be difficult on occasions as these tumble dryers dry the clothes using Refrigeration process.

This video will show you how to enter test mode on Heat pump tumble dryer test mode Aeg, Electrolux, John lewis, Zanussi, tumble dryers.

On the website we have the list of Error codes as well as the service manual.

[robhayward]

I have the AEG T7DBG832R which has an all touch screen display.
In this version I found (by trial and error) that you need to hold the "Start" and "Refresh" buttons and not the delay start.
The diagnostics come up but continue flashing through all the lights until you turn the control to one of the options.

[DoomZoone]

The Electrolux is kind of dead.. no lint, no water collected, but tomorrow - it'd be party time! All fingers crossed and HUGE Thanks for the great video tutorials!

[shmuelperlberg]

I wonder what kind of computer size fan, located near the compressor?
Dc/ac voltage? I dont see its working. Hot point dryer.

[globalste]

Is there a video for replacing a belt on a JL heat pump drier? The back panel is all moulded and glued so you can’t use the method of disconnecting the bearing like on your other videos

[monzarace]

I have a slightly different AEG, namely a T87685IH3, and I cannot use the same method to enter testmode. Very annoying. Do you know how to get into testmode on this model?
If I use the normal method as you demonstrate here, the tumbler shows "dem" in the right side of the display, meaning demo mode.

Thanks.

[clearenceover]

Thank you man, your video helped me to resolve my issue. 😊

[simonvidajewelry]

Thank you for sharing this detailed video. It helped me a lot 🙏🙂

[MrMehmet]

Hi I have aeg 8000 series lavatherm absolutecare system dryer. Start pause button flashes and it cannot start. What could be the error? I think the first time capacitor failure? What do you think? How can you run a diagnostic program on it?Thanks for the help.

[olgatebraake]

thank you Guys so much! I fixed my heat pump tumble dryer with the help of your videos!

[MrRichard]

Very cool video, makes it easy to troubleshoot.... Should be in the manual this info.... Bought aeg 7000 series, we like it... Way better than the old system we're the hot air is vented to the outside....

[monzarace]

While in testmode, program 8, redo the sequence of pressing the same two buttons, and you will clear error codes.
Kind regards,
Redfox.

[stables]

I have a Zanussi dryer that’s not turning on (no sounds or LEDs) I’ve checked fuse etc but wondered if there were any common faults ?

[MultiDave]

hi can you please tell me where the dry sensor is for the AEG T56830 Lavatherm as it is not drying properly .have cleaned all the filters and the matrix and reset the sensor to the top setting buy using the Adjust ’level of dryness’
detection:
In the programming options .many thanks Dave

[rorygallacher]

Hello nice video.
During normal drying the dryer stops and I get E20. If I restart it, it works again for some time and then Iget E20 again.
I entered Test Mode and in C2 the pump works for 5 or 6 seconds and then I get E23 error.
I tried a different pump and the same happened in test mode and in normal drying operation also.
Could it be the printed circuit or some of its components or the float sensor next to the pump?

[joelvantwillert]

My dryer doesn’t start, but does not show an error code. Got it into service mode like you showed. When I select C5, the display shows 017 and 016 and then ‘ESE’ after a couple of seconds. I imagine this has something to do with the drum is not spinning(?). Would you have any idea what the issue could be?

[antonionkrapollari]

Hello!!I have the lavatherm AEG..the cooling fan its not working in the test mode..and the dryer stop the error code its e60 but in the 3 fist position of the test mode e63..i dont understand what is going.can i have your help?

[davedebang-bang]

Hi. Don’t suppose there is any way I can change any settings. I want the reverse tumble to last longer

[nontitcha]

hello thanks for the video.
I have E60 i suspect this is comming from the heat pum but i'm lost..
Do you have a video for this specific error?
I've tried to see the spare parts on your website but not easy to find with machine reference...
Thanks for your feed back.
Philippe from belgium

[chrisneale]

I have almost the same JOhn Lewis dryer but it is 7kg and no window in door. I can't get it into diagnostic mode after many attempts. Am I missing a trick?

[fogrisk]

If I have E32 on position 8 and 9?? Is it heat pump wrong? Thx