Real-Time Network Configuration For Network Engineers | VLANs, DTP, HSRP, OSPF, NAT, VPN

Join this channel to get access to perks:

Hello, Welcome to PM Networking...
My name is Praphul Mishra. I am a Network Security Engineer by profession and a Certified Cisco trainer by passion.

About this video:-
Real-Time Network Configuration For Network Engineers | VLANs, DTP, HSRP, OSPF, NAT, VPN

CCNA Configuration Playlist:-

1. Basic Routers and Switches Configuration
2. Packet Flow
3. Real Devices Configuration
4. EIGRP A-to-Z
5. VPN
6. Subnetting
7. OSPF A-to-Z
8. FHRP
9. STP
10. Voice over IP
11. Troubleshooting
12. ASA
13. EtherChannel
14. BGP
15. Policy-Based Routing
16. IPv6
17. VRF
18. MPLS

Our Social links:-

#ccna #ccnp #ccie #network_troubleshooting #networking_interview #network_configuration #network_engineer #network_engineer_training #cisco_network_configuration #router_configuration #switch_configuration #firewall_configuration #interview_questions_network_engineer #real-time_network_configuration #scenario-based_network #network_troubleshooting #network_troubleshooting_network_engineer #cisco_network_configuration #basic_network

[sandipanaec]

Aspiring network professionals should watch the video and practice its content. This will help you troubleshoot real-time problems effectively.

[vishalkataria]

Owesome toppic for learning prospective 😊 Thank you Sir

[lovenature]

Really very helpful, hope will see more videos with more advance configuration, if possible please make one video on data center devices like NEXUS from sctrach.

Thank you very much

[AliAhmed-szli]

You made all those topics in one video awesome ❤

[wintersolstice]

Hello PM Networking,

Thank you for this video. I learned some new stuff as I followed the video. I tested it on Packet Tracer and I got the same error of the bouncing OSPF neighbor adjacency between Router1 & Router2. I removed the "default-information originate" command in Router1 and the OSPF adjacency became stable. I tried removing the said command because I had experienced a similar error with tunneling and the cause was route recursion (that the router's own WAN route is being advertised back to it).

[phpBasics]

Nicely done. However, I would recommend IPsec as opposed to GRE, although IPSec configuration is not covered on the CCNA exam.

[Simplyanthonyr]

This video was a good refresher and well taught! Thank you!

[AliAhmed-szli]

❤thanx for good knowledge and explanation, thanks pro

[AnilKumar-tmfq]

Good video Please more such topics, please make project like Bank management, hospital management and small office management

[ankitsingh]

sir, ye sab jo aap ne iss video mei bataya ye ccna mei padaya jata hai ya ccnp mei?

[franklinenoronha]

Hi SIr, Very good video.. Can you also do a video if the traffic is going into the firewall form distribution switch before going outside to the router via a portchannel

[qtpvydl]

I was also wondering about outside NAT.

[amirking]

Hello sir I complete the whole senario by myself and then I realized the connection between servers and clients are ok and we can replace the server and client place with each other and then give service like DNS and AAA and .... to the clients but the problem was ospf neighborship so we can replace ospf with static routing I try it and the connection between two branch got ok

[alwinposadas]

need to name the router id other than the ip address of tunnel interface to eliminate recursive routing error on OSPF so the routers can advertise tunnel network on each other using the GRE tunnel. the purpose of default route on the routers is to keep the tunnel interface up.

[HH-cbmi]

Thank U so much. Could you Pls Replace 2 DSW with 2 Routers and configure sub interfaces and Apply HSRP in New video.

[thepuldarshana]

much needed tutorial for me. but again You missed out a firewall here. would have been great with a firewall. anyway thanks for this

[praohyderabad]

Can we use bgp in this scenario on all serial interfaces

[galaxyspace]

sir can you configure a ASA firewall as fail over and set a DMZ for those servers please ?

[matthewespinosa]

Hola, se podría configurar EtherChannel en esta topología ? En donde se lo aplicaría ?
Saludos desde Ecuador

[MariaGomez-lgug]

I notice that you are the only one who responds to the comments, I have a question, I always see topologies of this type and I see that they do the routing by imagining the scenario but in a CAMPUS LAN NETWORK I ONLY SEE MORE SWITCHES THAN ANYTHING ELSE I DON'T SEE THAT OF THE I only see DEEP ROUTING on the ISP side, but the internal routing of a LAN IS DONE BY THE CORE OR DISTRIBUTION SWITCHES. What can you tell me about this?

because I have seen all your videos and I have learned the OSPF AREAS AND ALL THAT but I have never seen a CAMPUS LAN topology SEE THAT ABOUT THE AREAS, IT IS ONLY FROM THE ISP THAT DOES SO MUCH ROUTING